User manual VTECH VT 2453

[. . . ] Congratulations on your purchase of this VTech product NEED HELP? Our representatives are here to help you with any questions concerning the operation of this product, available accessories, or any other related issues. Call Toll Free: 1-800-595-9511 In Canada, Call: 1-800-267-7377 or visit our website at www. com 1 Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: 1. Do not use this product near water (for example, near a bath tub, kitchen sink or swimming pool). Do not place this product on an unstable surface, such as a table, shelf or stand. [. . . ] With Toll Saver active, the system answers after two rings when you have new messages and after four rings when you have no new messages. NOTE: You can exit Feature Setup at any time by pressing a MAILBOX button. 25 Basic Operation Use SELECT to choose the remote access code you will use to access features and functions of the answering system from a touch tone phone. NOTE: To advance the remote access code by 10, press and hold SELECT. Answering System Operation At The Base Listen to, Save & Delete Messages The system automatically saves your messages until you delete them, and can store approximately 15 minutes of messages, memos, and announcements (up to a maximum of 99 messages). Your caller can leave a message of up to 4 minutes in length. If all messages in a mailbox have been reviewed, the key will glow steadily. A mailbox containing both old and new messages will play only the new messages first. After all new messages are played, press the MAILBOX key again to hear all messages. Before playing a message, the system announces the day and time it was received. While the message plays, the Message Window displays the number of the message. After playing the last message in a mailbox, the system announces " nd of messages. " If the system has less than five minutes of E recording time left, it announces remaining time. Basic Operation Note: When listening to your messages, if after the date and time stamp your system announces "power failure" it is alerting you that your date and time stamp is no longer accurate due to a power outage. Message Window Press to skip to the next message; hold to speed up playback. Play Messages Press to play messages in a mailbox. Press again to stop playback. Press to repeat a message; hold to slow down playback. Delete Messages · Press DELETE · You cannot · To delete a message, press then press a MAILBOX button to delete all old messages in that mailbox. 26 DELETE while the message is playing. delete a message until it's been reviewed; deleted messages cannot be recovered. Answering System Operation At The Base Call Screening/Intercept 1. Make sure the answering system is on, and set the message playback volume control above level 1 so you can hear the caller' message. If you pick up an extension phone during the announcement and the announcement does not stop right away, press and release the telephone switchhook. Record a Memo You can record a memo up to four minutes long, which is stored as an incoming message. To stop recording, press the MAILBOX button again. Message Window Display Window Display: when: 0 1 - 99 0 - 99 F No messages in any mailbox Total number of messages in all mailboxes, or message number during message playback. Memory is full, or total number of messages is 99 Duration of memo recording. System is in programming mode or initializing. 1 to 99 (Counting) 99 (flashing) 1 - 8 (on steady for one second) 40 - 99 A On or OFF (steady for one second) CL --- (flashing) 27 Basic Operation Answering System - Remote Access Connect with the Answering System You can access many features of this system remotely from a touch tone phone. When the system answers, enter your Remote Access Code (preset to 50). Voice Menu The system has voice prompts to help you with remote operation. Press * 5 to hear the menu while remotely connected to the answering system. Remote Access Commands Function: Play messages in a mailbox Command: Press # , then the appropriate mailbox number (1, 2, or3). Press #4 while message is playing; press #4#4 to back up previous message. Press #6 while message is playing; each press advances up another message. System plays back announcement. Basic Operation Repeat a message Skip a message Stop Save messages Delete message Review announcement Record announcement 28 Answering System - Remote Access Remote Access Commands (continued) Function: Function: Command: Record memo Command: Press *8 , then mailbox number where you want memo recorded; speak after beep; press #5 when finished. Press #0; the system announces, " nswering machine off. " Press # 0 A again to turn the system back on. [. . . ] · Programming/testing of emergency numbers should be performed during off-peak hours, such as in the early morning or late evening, when the emergency services tend to be less busy. The term "IC:" before the radio certification number only signifies that Industry Canada technical specifications were met. Notice: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. [. . . ]