User manual VTECH VT 1122

[. . . ] IMPORTANT SAFETY INSTRUCTIONS CAUTION TO REDUCE THE RISK OF INJURY TO PERSONS, READ AND FOLLOW THESE INSTRUCTIONS. 1 Use only the type and size batteries designed for this product. Released electrolyte is corrosive and may cause damage to the eyes or skin. 3 Exercise care in handling batteries in order not to short the battery with conducting materials such as rings, bracelets and keys. 4 Do not attempt to recharge the batteries provided with or identified for use with this product. [. . . ] The phone returns to Pulse dialing when you hang up. Blocked or Unavailable Calls 1 If the caller's telephone number is blocked (that is, the caller wishes to keep his telephone number private), the display will show PRIVATE in place of the caller name. 2 If the call is international or from an area where Caller ID service is not available, the display will show UNKNOWN in place of the caller's name. Note: We recommend that you disconnect the phone line when programming your telephone. Reviewing Calls 1 The NEW CALL indicator will flash to indicate new calls or calls that have not yet been reviewed. 4 After a new call is reviewed, it will be deducted from the total number of new calls displayed. 5 When the list of calls reaches the end, the display will display END OF LIST and return to show the current time and date in 10 seconds. MUTE Button 1 Press and hold the MUTE button when you don't want the other party to hear the conversation on your end. 2 Release the MUTE button to return to two-way conversation. TONE/PULSE Switch 1 The DP (PULSE) position is used if your local telephone system offers only Pulse (rotary dial) service or if Tone service is available but you do not subscribe to it. 2 The TT (TONE) position is used if you subscribe to Tone Dialing (DTMF) service. If you are not certain what type of service you have, check with your local telephone company. 1 Lift the handset. 4 Press the one-touch button (M1, M2, M3) where you want to store the number. When you hear the dial tone, dial the phone number you are calling using the buttons (1 to 9 and 0). When your call is completed, hang up the handset. CALLER ID OPERATION Receiving a Call When you receive a call, your unit will display the caller information sent by the telephone company including: · The caller's name (if available) · The caller's telephone number (if available) · The date and time of the call · The Call Number to indicate the sequence of the call Note: When the memory is full and new calls are received, previous messages will be replaced by the new calls. REDIAL Button The last number you have dialed (up to 32 digits) remains in memory known as last number redial memory. If you call a number and receive a busy signal or no answer, hang up the handset. When you are ready to try the same call again, pick up the handset and tap the REDIAL button. Please note that if you have made any other calls in the meantime, only the last number you called will be stored in the redial memory. To delete an individual call: 1 Press the UP or DOWN button until the call to be deleted is displayed. 3 The call is deleted and the total call count is reduced by 1. To delete all calls: 1 While the idle screen is displayed, press the REMOVE key and hold it until the LCD displays "REMOVE ALL?" 2 Press the REMOVE key again to delete all calls and the total call count returns to zero. Replacing a Number Stored in Memory Follow Steps 1-5 (one-touch) or 1-6 (two-touch) in Storing a Phone Memory. Deleting Numbers Stored in Memory 1 Press the PROG button. 2 Press the one-touch button you want to delete, or press MEM and the dialing key of the location you want to delete. Dialing from Displayed Call 1 Press the UP or DOWN button until the desired call is displayed. Your call will be dialed automatically. FLASH Button For residential phone systems with "Call Waiting" service, instead of pressing the hook switch to pick up the other call, press the FLASH button. This will automatically send the correct signal to the telephone company to switch calls. The amount of time you hold the FLASH button down is not critical. Caller ID This telephone is compatible with "Caller ID" service. Make sure that your telephone company offers this service and you have subscribed to it in order to use this service. Recalling a Number from the One-Touch Memory 1 Lift the handset. 2 Press the one-touch button (M1, M2, M3) where the number you want to call is stored. 3 Your call will automatically be dialed. 6 7 8 WARRANTY STATEMENT & FCC REGULATIONS Limited Warranty · What does this limited warranty cover? [. . . ] An applicable certification jacks Universal Service Order Codes (USOC) for the equipment is provided (i. e. , RJ11C) in the packaging with each piece of approved terminal equipment. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. [. . . ]