User manual VOYAGER VOM-78T

[. . . ] Be sure this line is infused with an in-line 3-Amp Blade or Glass Fuse. 5) PA Installation The PA should be mounted in a DIN sized opening on the vehicle' dash. 6) MIC Installation a) MIC extension plugs into the back of the VOM-78T unit. c) Depending on the construction of the luggage rack, two mounting plates may be required to support monitor assembly. [. . . ] (from top of luggage rack down) f) Place a mounting plate washer, lock washer, and nut on bolt and tighten to 100 In. lbs. g) Place a nut, lock washer, and washer on bolt prior to putting mounting bracket in place. Place mounting bracket in position and assemble washer, lock washer, and nut to hold bracket in position. i) Slide monitor into position and hand tighten two ¼-20x1" bolts to hold monitor in position. (Fig. 10) j) Connect video in/out (6-pin connector) and power (4-pin pigtail). Splice two 14G orange from harness to one 14G orange from pigtail, connect two 14G black from harness to one 14G black from pigtail, connect two 18G blue/white from harness to 18G blue/white of pigtail. k) Install remaining ¼-20 grade 8 bolts and tighten all four to 100 in. l) Clean four tabs of mounting bracket with a 70% solution of isopropyl alcohol. m) Place two 1" x 1" and 1"x 2'pads of " dual lock"velcro on mounting bracket. 10) n) Place padded shroud over monitor assembly and locate position of mating velcro pad. If a 10°wedge base is used, be sure shroud is flush to all edges prior to attaching velcro. (Table 1 and Figure 8) 7) Audio In- Supplies audio from VCP, monitor and radio. 5 VOM-78T Harness Details IR LED: Clean the IR Receiver window on the front of the VCP, remove adhesive backing and apply IR LED to IR window on the face of the VCP. IR Harness Speaker Out Harness Power Monitor Trigger Out Harness Connects to monitor power control in Audio Input Harness Figure 5 6 Front Monitor Details 1 Figure 6 1) Power Indicatora) Will illuminate bright red when monitor is triggered " by the PA on" system. b) Will illuminate dim red when monitor is triggered " by the PA off" system. 7 Rear Monitor Features Video In (-) 2 Video Out (+) 3 12-24VDC 1 Video In (+) Video Out (-) 4 Chassis Ground Trigger From PA 12V Figure 7 Monitor Operating Controls 1) Picture Selectora) " Press"left most button to trigger " screen display. " Order of On control: Contrast, Brightness, Tint and Color. b) Use the " and " buttons to increase or decrease the setting to +" -" achieve the uniformity of each monitor in your application. 2) Video Input/Output Connectora) Mating Connector: Amp P/N 172168-1, Mating terminal: Amp P/N 171637-1. b) See Table 1 and Figure 8 for customer insertion view and harness color code. 3) Monitor Power Controla) Mating connector: Amp P/N 172167-1, mating terminal: Amp P/N 171637-1. b) See Table 1 and Figure 8 for customer insertion view and harness color code. 4) Monitor Fuse*Replacement fuse should be a 5 Amp automotive glass fuse* Do not replace with a higher or lower rated fuse. An over rated fuse will allow excessive current draw to damage the monitor. An under rated fuse will fail during power up or cause heat damage to the fuse holder or monitor (depending on the rating of the fuse). [. . . ] Rear (+) VCP 4 Input Power/ Ground Monitor 5 6 7 8 External Speaker Passenger Side Speaker Driver Side Speaker 12VDC Chassis Ground 24VDC 12 to 24VDC Chassis Gnd (from VCP) (to 2nd, 3rd, 4th, etc. ) Speaker (+) Speaker (-) Speaker (+) Speaker (-) Speaker (+) Speaker (-) Table 1 9 Harness Layout 7 7 5 7 8 8 6 7 5 8 5 3 8 5 2 1 1 4 Optional PA location Figure 8 10 Monitor Installation Diagram COMPRESSION PLATES (OPTIONAL) HARNESS 1" x 1" VELCRO STRIPS ON 2-SIDES 9" MONITOR 5/16 x 18 UNC GRADE 8 CARRIAGE BOLTS LUGGAGE RACK WEDGE BASE MOUNITNG BRACKET W/BOLTS 12-24VDC CHASSIS GND TRIGGER VIDEO IN VIDEO OUT MONITOR PIGTAIL 1/4X20 BOLT GRADE 8 4 PLACES 1" x 2" VELCRO STRIPS ON FRONT AND BACK VINYL WRAPPED SHROUD DRIVER SIDE PASSENGER SIDE Figure 9 11 Exploded Monitor Installation View (4) - 5/16x18 UNC Grade 8 Carriage Bolts (P/N 8001500) Compression (Crush) Plate (Optional) (P/N 1400003) Compression (Crush) Plate (Optional) (P/N 1400003) (2) - 1X1 Dual Lock Velcro Tape (P/N 8001508) (2) - 1 X 2 Dual Lock Velcro Tape (P/N 8001508) (4) - 1/4X20X1 Grade 8 Bolts (P/N 8001501) and Washers (P/N 8001503) (12) - 5/16X18 Grade 8 Nuts (P/N 8001030), Washers (P/N 8001502) Lockwashers (P/N 8001504) 10° Wedge Base (Optional) (P/N 1400150) (2) - 1X1 Dual Lock Velcro Tape (P/N 8001508) Monitor (P/N BV0901) (2) - 1 X 2 Dual Lock Velcro Tape (P/N 8001508) Shroud (P/N RPVBSH91) Figure 10 12 Speaker Connections To obtain optimum sound pressure level, and compatible load, please use the speaker connection methods illustrated. 18 GRN(+) PASS. SIDE SPKR 18 GRN/BLK (-) 18 GRY (+) DRIVER SIDE SPKR 4 or 8 18 GRY/BLK(-) 18 GRN(+) PASS. SIDE SPKR 18 GRN/BLK (-) 18 GRY (+) DRIVER SIDE SPKR 4 Ohm only 18 GRY/BLK(-) 18 GRN(+) PASS. SIDE SPKR 18 GRN/BLK (-) 18 GRY (+) DRIVER SIDE SPKR 4 Ohm only 18 GRY/BLK(-) 18 GRN(+) PASS. [. . . ]