User manual VOSONIC X-DRIVE II

[. . . ] Driver Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Windows Me and Windows XP HomeEdition and Professional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Macintosh MacOS 8. 6 and 9. x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Under Windows 98, Windows 2000 Professional, the 4 Removable disk drives look like drives F, G, H and I in the following figure. · Under Windows Me, Windows XP, the 4 drives are shown in the usual Removable drive way . X's-Drive VP2060 8 When X's-drive II is begin connected to the computer, the " Transfer" icon keeps flashing during data transfers, when inserting a memory card into the slot, the corresponding icon will appear and also flashes during data transfer. Until the flashing icons are ceased to flash and buzzer sound "Bi Bi "Operation system with native support: DO NOT: 1. Remove memory card(s) from the card slot Otherwise, there may be a chance of lost or corrupt data. Under Windows 98SE, the X's-drive II should be connected to the system before the driver has been installed. Under Windows 2000 Professional, the X's-drive II should be connected to the system before the driver has been installed, only one Removable drive will appear in My PC, corresponding to the SD/MMC/MS memory slot. In this case, the driver must be installed and then it must be updated by means of the Device Manager. The X's-drive II is supported by the native MacOS X USB extensions, but DOS volumes are not adequately supported by MacOS 10. 0. x and lose of data can occur. Upgrading to version 10. 1 or later is mandatory. 9 X's-Drive VP2060 Data Transfer All files transfered from each memory card are stored onto the Hard Disk in folders numerically, under the name "CF0001" , "MS0001" , "SM0001" , "SD0001". To stop the data transfer, just depress the copy button for 2seconds and the memory card(s) icon will cease to flash , the buzzer will sound"Bi Bi", then you can switch off the device. Once download is complete, the flashing icons will cease to flash and buzzer will sound. When the same card was inserted and copied twice, two different folders were created, X's-drive II won't overwrite the folder. Battery Recharge: To charge the batteries, connect the plug of the AC adapter to DC 12V jack of the main unit, and when the LED indicator in the right upper side is off, it indicates that the batteries were fully charged. Before using the recharge battery for the first time, charge it for 8hours, each full recharge takes approximately 3 hours. The 3. . 6V Li-ion rechargeable battery can be recharged approximately 500 times. Only use the Li-lon rechargeable battery (3. 6V x 2 ), for additional battery packs, please contact your dealer. Auto Power off Function: To preserve energy in stand-alone mode, X's-drive II will automatically shut-off if you do not execute the copy function during 25 seconds. X's-Drive VP2060 10 If an erroneous display /operation occurs: When the icom indicator of error & corresponding memory card light up, there may be a chance of corrupt data or the memory card is damaged, you can change another memory card or the main unit will be automatically switched off after 45 seconds. If any shut dowm caused by erroneous operation, you can depress the [reset] button located on the at the right side to switch off the main unit. If the unit operated via USB on to PC while the batteries are low, erroneous display / operation may occur, if this happens, unplug the USB cable, and press the [reset] button. Care for the Hard Drive: If the computer or X's-Drive II can not detect the Hard Drive, check the suggested solutions: · Check the flat connector is pluged securely or not · Driver is not install-then reinstall · Formated the Hard Disk under Windows 2000 Please don't use force when connecting the flat cable with the unit and Hard Drive. To keep your hard drive in better operating performance, we recommend to periodically run Scan Disk and Disk Defragmenter. I formated the disk by the MacOS X's Disk Utility, but it lasts very long in being mounted by either MacOS 9 or X, and Windows does not recognize the volume. Under MacOS X 10. 0. x I have many problems with the disk, and I have even lost information Cause The X's-drive II has been connected before installing the driver. Solution The driver must be installed before connecting the X'sdrive II. The hard disk device has been ejected. Install the extension. MacOS X issue. Move the mouse. Sometimes the FAT volumes do not appear or disappear until after the mouse is being moved. MacOS X issue. The FAT-32 format made by MacOS X's Disk Utility is incorrect. Formating must be done under MacOS 9. MacOS X issue. MacOS 10. 0. x does not adequately support FAT volumes. [. . . ] The memory card will work fine after. In case that the X'S-Drive II hangs, you can reset it via this button-note that the data on the Hard disk will not be affected. 17 X's-Drive VP2060 Question My computer only has USB-1 ports available. Can I format the X's-Drive II to the NTFS/HFS/ HFS+/EXT2, etc, file systems?Can I share the X's-Drive II among MacOS, Windows and Linux? Answer The X's-Drive II is an USB-2 device, but it does not matter. Both USB-1 and USB-2 devices can be connected to USB-1 ports, as they are detected and managed in the corresponding way. [. . . ]