User manual VITEK VTM-14C-H

[. . . ] 8) Accessories Do not place this product on an unstable cart, stand, tripod, bracket or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. [. . . ] 10) Ventilation Openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 2 SAFETY INSTRUCTIONS 11) Power Sources This product should be operated only from the type of power resource indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For products intended to operate from battery power or other sources, refer to the operating instructions. 12) Grounding or Polarization This product is equipped with a three-wire grounding-type plug a plug having a third (grounding) pin. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. 13) Power-Cord Protection Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. 14) Protective Attachment Plug The product is equipped with an attachment plug having overload protection. See instruction Manual for replacement or resetting of protective device. If replacement of the plug is required, be sure the service technician has used a replacement plug specified by the manufacturer that has the same overload protection as the original plug. A standard 1. 0 Vp-p video signal applied to the VIDEO INPUT will also appear at the VIDEO OUTPUT. S-VIDEO JACK If the camera or other video source outputs an S-VIDEO signal, connect it directly to this jack. AUDIO INPUT & OUTPUT CONNECTORS Connect an RCA cable between these jacks and the audio output jack of a camera or VCR. 5 OSD MENU ADJUSTMENTS Access the OSD Menu: Press the MENU button and use the arrow up/down buttons and arrow left/right to navigate the menu system. Contrast adjustment: Adjust the CONTRAST control for the desired overall display contrast. Proper adjustment will allow maximum gradations between the darkest and lightest picture areas. Brightness adjustment: Adjust the BRIGHTNESS control for the desired overall display brightness. This control is also useful to compensate for differences in area lighting. Color adjustment: Adjust the COLOR control to set the color saturation level. Sharpness adjustment: Adjust the SHARPNESS control to set the sharpness level. Tint adjustment: Adjust the TINT control for the proper color phase or flesh tones. Scan operation: To move the cursor with the arrow up/down buttons and enter the next page by pressing the arrow left/right buttons. [. . . ] Change the scan operation to over/under by pressing the arrow left/right buttons. Degauss operation: To move the cursor with the arrow up/down buttons and enter the next page by pressing the arrow left/right buttons. Preset operation: To move the cursor with the arrow up/down buttons and enter the next page by pressing the arrow left/right buttons. When pressing the arrow left/right buttons, change adjustment value to factor condition. 6 CONNECTING THE MONITOR Video camera Audio Audio signal cable Video Video signal cable VCR Audio Video Video Monitor Video camera Audio Audio signal cable Video Video signal cable VCR Audio Video Video Monitor Video camera Audio Audio signal cable VCR Audio Y/C (S-VHS) S-VHS Signal cable 7 NOTES 8 NOTES 8 SPECIFICATIONS DETAILED SPECIFICATIONS Picture Tube Resolution Video System A/V Terminals Input Signal Sound output Speaker Power Source Power Consumption Operating Temperature Dimensions(W x H x D) Weight 14" diagonal with 90° deflection angle 450 TV Lines NTSC / PAL Looping BNC Video In/Out, S-Video Input, Audio In/Out Video Composite: 1Vp-p 1. 0 W 3W AC 100-240V~, 50/60 Hz 45 Watts 32°-106° F (0°-40° C) 13. 8" x 12. 9" 14. 6" (350 x 328 x 371 mm) 30. 9 lb (14Kg) 10 WARRANTY INFORMATION LIMITED LIABILITY WARRANTY VITEK monitors carry a two (2) year limited warranty FOB VITEK warehouse, except for CRT Monitors (picture tube) which carry a ninety (90) day warranty due to potential misuse. [. . . ]