User manual VITEK VTC-IRH70-650

[. . . ] Long Range Weatherproof IR Bullet Camera VTC-IRH70/650 VITEK · 1/3" Super HAD Color CCD · High Resolution with 560 TV Lines Resolution in Color (600 TV Lines in B/W mode) · 70 IR LEDs at 850nm enable viewing in Total Darkness up to 300 Feet · Simultaneous Color and Black & White Focus Adjustment · Infrared LED Dynamic Intensity Control with automatic brightness adjustment of IR LEDs to help prevent washed out images when objects are too close · Camera and IR LED compartments are separated using a dual glass design to prevent stray IR light from entering the lens · Vari-Focal 6~50mm DC Auto Iris IR Lens · Virtual Wide Dynamic Range · OSD control · Secondary Video Output & OSD Control Joystick are accessible inside a gasket sealed removable side panel · Externally adjustable Focus & Zoom with clutch mechanism to eliminate over-tightening · Gasket sealed external focus and zoom controls with clutch mechanism to eliminate over-tightening for ease of installation and adjustment · Heavy Duty IP68 rated Weather/Vandal Resistant Aluminum Construction is 100% water and dust proof · Fully adjustable 3 axis wire feed-through mount · Dual Voltage: 12VDC / 24VAC Table of contents 1. Safety Instructions and Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supplied Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Save and Exit. FACTORY SET EXIT NO - 6 6. 2 EXPOSURE menu To enter EXPOSURE menu, press at MAIN>EXPOSURE. EXPOSURE Factory Default Descriptions 1) If LENS at MAIN menu was set to DC, a fixed shutter is selectable from 1/60(NTSC) or 1/50(PAL), FLK, 1/250, 1/500, 1/2000, 1/5000, 1/10000, 1/100000 and a fixed sense-up rate is selectable from x256, x128, x64, x32, x16, x8, x4, x2. At x2~x256, DSS(Digital Slow Shutter) is operating with the selected frame integration rates regardless of the light level. When TV system is NTSC(PAL) and Main power is 50Hz(60Hz), set to FLK(Flickerless mode). 2) If LENS at MAIN menu was set to MANUAL, SHUTTER should be set to AUTO to get a proper video level with the automatic shutter range between 1/60(1/50)~1/100, 000sec. Color rolling or Video level hunting under Fluorescent or similar lighting may occur in this configuration. 1) If DAY / NIGHT at MAIN menu was set to AUTO or NIGHT, AGC is not user adjustable. Settings are not available if DAY /NIGHT at MAIN menu is set to AUTO SENSE-UP is available only when SHUTTER is 1/60(1/50) or AUTO. moves it rightward. increases WIDTH of BLC window moves it downward. moves BLC window upward and decreases and bottom. increases HEIGHT of BLC from the HSBLC OFF 9 HSBLC ON 6. 2. 3 D-WDR menu To enter D-WDR (Digital Wide Dynamic Range) menu, press at EXPOSURE > DWDR > ON. D-WDR improves the dynamic range of video by means of digital compensation for the dark and highlighted areas. D-WDR LOW COMP. Loads the default for D-WDR. 6. 3 DAY / NIGHT menu 6. 3. 1 DAY / NIGHT AUTO menu To enter DAY/NIGHT AUTO menu, press at MAIN > DAY/NIGHT > AUTO. When switched to NIGHT, camera removes its IR cut filter and switches to B/W mode. IR LED version Non-IR LED version IMPORTANT!!!DAY->NIGHT and NIGHT->DAY operations must be examined and verified at the final step of the installation. Block the lens for a few seconds for NIGHT mode and release and let it return to DAY mode. If camera stays at NIGHT mode more than 10sec, decrease N->D LEVEL a little and repeat the fore- mentioned steps. If the scene is too dim or lens iris was adjusted near close, it may not return to DAY. 10 DAY NIGHT AUTO Factory Default Descriptions DELAY is the duration which should maintain its status before making the D-->N or N-->D switches. Camera checks the light level seamlessly to determine if it crosses over the threshold levels of D-->N LEVEL or N-->D LEVEL. The state must maintain unchanged for longer than DELAY time in order to force switchover. DELAY is used to avoid the unwanted switching by short term lights such like the light from the passing car. Try NOT to make the gap too small between D->N LEVEL and N-->D LEVEL to avoid continual switching. TO EXIT NIGHT MODE AT BRIGHTER ILLUMINATION, INCREASE it and vice versa Try NOT to make the gap too small between D->N LEVEL and N-->D LEVEL to avoid the switch repeating. In B/W mode, BURST can be set to OFF(default) or ON in DAY/NIGHT B/W menu. BURST OFF shows sharper and better resolution however some equipment may function inconsistently with BURST OFF. [. . . ] of 8 Descriptions areas, AREA1~AREA8, to be ON If set to ON, the window selected by AREA SELECT appears and enables the privacy mask for that area and vice versa. decreases and increases WIDTH of the window selected by AREA SELECT from the right. decreases and increases HEIGHT of window selected by AREA SELECT from the bottom. Each area color can be selected individually. 8 WIDTH 16 VER. [. . . ]