User manual VITEK VTC-C770WDR

[. . . ] Setup Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dimensional Drawings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Instructions and Notes · Read instructions carefully before putting the camera into operation. [. . . ] Point the camera at an object with sufficient contrast at a distance of approximately 2 meters 2. Screw one~two turns on the camera with the industrial "+" driver 7. Steps 3, 4, 5 and 7 may need to be repeated several times to obtain the best results 8. Installation The camera has a 1/4" thread insert on its top and bottom side for mounting the camera to a tripod, wall or ceiling with a corresponding mount. 5. 4 Commissioning · First, connect the power supply to the power terminal on the rear panel of camera · Second, plug the power adaptor to the main supply · Power indicator LED will be lit · The camera is ready for operation 5. 5. Power Supply Connections The camera can work with either 24VAC or 12VDC, dual voltage power. Primary and secondary grounds are completely isolated to avoid the possible ground-loop problems. Its wide operating voltage range of 10. 5V-30V for DC and 12-28. 8V for AC gives extra flexibility at the installation. 6. Start up When the camera is powered properly, it starts up by initializing the internal parameters and the filter switch mechanism. The filter switch unit repeats IN and OUT at each power up and just after RESTORE FACTORY SETTINGS. 7 VTC-C770WDR 7. SETUP 7. 1 In the menu Use , buttons to move the menu, button to select or enter. 7. 2 Entering menu Press 7. 3 MAIN Follow the chart below for submenu settings button longer for than 2 seconds on the back of the camera. , buttons to change the settings and press MENU EXPOSURE Default Descriptions Sets COLOR ROLL COMP. , AE PREFERENCE, WDR CONTROL and SENSE-UP. Sets OFF, AUTO or NIGHT OFF ­ Day/Night is disabled and camera works as a normal color camera. COLOR SELECT, SHARPNESS, VIDEO DAY/NIGHT AUTO 3D NR LENS SELELT PICTURE CONTROL SPECIAL D-EFFECT EXIT DC Sets MOTION, PRIVACY MASK, STANDARD, RS485 CONTROL. Sets FREEZE, FLIP or D-PTZ. SYNC, LANGUAGE, Choose EXIT, SAVE AND EXIT or FACTORY SET. 8 VTC-C770WDR 7. 4 EXPOSURE To enter EXPOSURE menu, press button at MAIN>EXPOSURE. EXPOSURE EXPOSURE Default Descriptions Descriptions In NTSC system, the entire color tone on the monitor may continuously <WDR MID> Medium level ofreddish and greenish. - Reduces the color rolling under the fluorescent COLOR ROLL range control. ROLL OFF OFF flexible compensate the other than Provides more ­ Does notcompensation color rolling. LOW, WDR HIGH - Compensates the color rolling when an auto iris lens is MODE-A Compensates the brightness of main object against the bright used. Sets HIGHLIGHTS or SHADOWS HIGHLIGHTS - Provides the best detail in the brighter LOWER1/3 A zone out of CTR SPOT, UPPER1/3, MIDDLE1/3, areas. Increase the value if it stays in B/W and is required to switch to DAY. N<-->D DELAY is time in seconds while the camera maintains its status before D<-->N switches. [. . . ] Resolution Sensitivity S/N Ratio White Balance WDR mode Auto Iris Control SENSE-UP Motion Detection D-PTZ FLIP Privacy Zone Auto Iris Control Flicker reduction OSD Video Output Lens mount Operating Power Operating condition Dimension (W x H x L, ) VTC-C770WDR VTC-C770WDR/PAL Pixim D8800C Seawolf Digital Imaging System CMOS 768(H) x 540(V) NTSC 59. 94Hz(V), 15. 734Khz(H) Internal/Line lock (Default: Internal) 700TV Lines 0. 0008Lux at F1. 2@40IRE, 32x (DSS+ICR mode) 50dB with AGC OFF at 50IRE 2, 000 ~11, 000ºK Automatic tracking / AWB / MANUAL 4 presets [Low / Middle / High / Custom (User Adjustment)] DC drive iris control 2X, 4X, 8X, 16X, 32X, 64X ESS On/Off (4 Programmable Zone) Up to X12 digital zoom OFF / H-FLIP / V-FLIP / H/V-FLIP On/Off (6 Programmable Zone) DC Drive Iris Control Yes (NTSC Japanese version only) Yes (Setup menu only) VBS 1Vpp +/-10%, 75ohm C/CS (C-mount ring - optional) 12VDC / 24VAC 3 Watts / 220 mAmp -4'F ~ 122'F / -20'C ~ 50'C, 85% RH. Non-condensing 2. 56 x 2. 17 x 4. 17 (in) (65 x 55 x 126-mm) ~9. 5oz (270g) (Net) PAL 50Hz(V), 15. 625Khz(H) Design and specifications are subject to change for product improvements without prior notice. 17 VTC-C770WDR 9. Dimensional Drawings 18 VTC-C770WDR 19 VTC-C770WDR VITEK LIMITED PRODUCT WARRANTY VITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user. [. . . ]