User manual VITEK VTC-C770DN

[. . . ] 700TVL True Day and Night (ICR) Camera VTC-C770DN VITEK · 1/3" Sony High Density EXVIEW CCD · Sony Effio Digital Signal Processor · 700TVL High Resolution · . 003Lux (F1. 2@50IRE) · Supports C/CS mount DC drive lenses · Supports NTSC & PAL Standards · Adaptive Tone Reproduction · 2DNR - Two Dimensional Motion Adaptive Noise Reduction · Motion Detection · Privacy Mask · On Screen Display (OSD) Menu · 24VAC/12DC Dual Voltage VTC-C770DN WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit. This symbol is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to a person. Caution To prevent electric shocks and risk of fire hazards, do NOT use other than specific power source. Warning (NTSC version) -- This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their expense. Caution -- Any changes or modifications in construction of this device that are not expressly approved by the party responsible for compliance, could void the user's authority to operate the equipment. 1 VTC-C770DN Table of contents 1. [. . . ] Areas and gains for HLC and BLC are factory preset and not user adjustable. To save the changes, move cursor to 'SAVE ALL' and press button before exiting the setup menu. Saves all parameters by pressing 8 8 button. DAY/NIGHT AUTO PICT ADJUST WHITE BAL ATR BACKLIGHT NEXT EXIT SAVE ALL ATW OFF OFF VTC-C770DN 6. 2. 1 MAIN menu-2 MAIN menu-2 NR MOTION DET PRIVACY LANGUAGE Default OFF OFF ENGLISH Descriptions Sets the noise reduction parameters for NR MODE, Y LEVEL and C LEVEL. User programmed camera ID will be lost and restored with Factory default ID after CAMERA RESET. To save the restored parameters, move cursor to 'SAVE ALL' and press button before exiting the setup menu. Sets the brightness level which starts AGC from x0. 25, x0. 50, x0. 75 and x1. 0 of full video level. If set to x0. 50, the camera will start AGC when the video level goes down to below the 50% level. NOTICE : The setting AUTO IRIS at SHUTTER/AGC>AUTO SETUP>HIGH LUMINANCE MODE will be changed to SHUT+AUTO IRIS if MAIN menu-1>LENS is changed to MANUAL. As a result, the lens iris can NOT be fully opened when MAIN menu-1>LENS>AUTO IRIS> MODE is OPEN. This can be recovered by setting SHUTTER/AGC>AUTO SETUP>HIGH LUMINANCE MODE to AUTO IRIS. HIGH LUMINANCE x0. 50 10 VTC-C770DN 6. 3. 2 SHUTTER/AGC>MANUAL SETUP menu MANUAL SETUP MODE Default SHUT +AGC 1/60 (1/50) Descriptions Compensates the video level by the manual shutter control and AGC. Sets the manual shutter to 1/60(1/50), 1/100(1/120), 1/250, 1/500, 1/1000, 1/2000, 1/4000 or 1/10000. Manual AGC can be set to 6, 12, 18, 24, 30, 36, 42 or 44 8dB. SHUTTER AGC 6. 00 6. 4 LENS menu To enter LENS menu, press button at MAIN menu-1>LENS>AUTO. AUTO IRIS TYPE Default DC Descriptions MUST BE SET TO DC ONLY. This camera does NOT support video type auto iris lens. AUTO ­ Lens iris is automatically controlled according to the scenes light level. If the speed is too slow or fast, the iris control may be unstable. MODE AUTO SPEED 080 6. 5 DAY/NIGHT menu To enter DAY/NIGHT menu, press button at MAIN menu-1>DAY/NIGHT 11 VTC-C770DN IMPORTANT ACTIVITY!!! DAY->NIGHT and NIGHT->DAY operations must be examined and verified at the final installation. Block the lens for a few seconds for NIGHT mode, then release and let it return to DAY mode. If camera stays at NIGHT mode for more than 10sec, slightly increase , , ND THRES and repeat the forementioned steps. If the scene is too dim or the lens iris was adjusted too low (near close), it may not return to DAY. DAY/NIGHT Default Descriptions BURST mode contains color burst signal when the camera switches to B/W. ON mode maintains the same color signal in B/W so that the video signal provides better compatibility with certain color equipment. OFF mode removes the color burst signal B/W video and increase the total TV lines. DELAY can avoid the unwanted/frivolous switching of short term lights such as light from a passing car. DAYNIGHT mode sets a threshold level to determine when switch from DAY to NIGHT. Lower (Higher) value makes the camera switched from Day to Night at lower (higher) illumination. If the camera stays in Color at night time, increase DAYNIGHT threshold value until it just switches to Night. CAUTION If the value between DAYNIGHT and NIGHTDAY is minimal, then camera may switch between DAY and NIGHT mode repeatedly. [. . . ] Enables or disables displaying blocks for the area where the motion is detected. Selects AREA1~AREA4 to be adjusted. BLOCK DISP MONITOR AREA AREA SEL 1/4 TOP (BOTTOM) button moves up and button moves down the top (bottom) border of the selected window at AREA SEL. LEFT (RIGHT) button moves left and button moves right the left (right) border of the selected window at AREA SEL 6. 12 PRIVACY menu Up to 8 privacy areas are available and each area is programmable in size and location. The number of privacy areas is limited to four when MOTION DET>MONITOR AREA is ON. [. . . ]