User manual VIA P4M800

[. . . ] 5 Chapter 2: Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2. 1 2. 2 2. 3 2. 4 Installing Central Processing Unit (CPU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 FAN Headers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Installing System Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This connector supports the provided floppy drive ribbon cables. PU 2 34 1 33 IDE1/IDE2: Hard Disk Connectors The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality. The IDE connectors can connect a master and a slave drive, so you can connect up to four hard disk drives. The first hard drive should always be connected to IDE1. PU IDE1 40 39 2 1 IDE2 9 P4M800 PCI1~PCI3: Peripheral Component Interconnect Slots This motherboard is equipped with 3 standard PCI slots. PCI stands for Peripheral Component Interconnect, and it is a bus standard for expansion cards. This PCI slot is designated as 32 bits. PU PCI1 PCI2 PCI3 AGP1: Accelerated Graphics Port Slot Your monitor will attach directly to that video card. This motherboard supports video cards for PCI slots, but it is also equipped with an Accelerated Graphics Port (AGP). An AGP card will take advantage of AGP technology for improved video efficiency and performance, especially with 3D graphics. PU 10 P4M800 CNR1: Communication Network Riser Slot The CNR specification is an open Industry Standard Architecture, and it defines a hardware scalable riser card interface, which supports modem only. PU 11 P4M800 CHAPTER 3: HEADERS & JUMPERS SETUP 3. 1 HOW TO SETUP JUMPERS The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is "close", if not, that means the jumper is "open". Pin opened Pin closed Pin1-2 closed 3. 2 DETAIL SETTINGS This connector allows user to connect 20-pin power connector on the ATX power supply. Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Assignment +3. 3V +3. 3V Ground +5V Ground +5V Ground PW_OK Standby Voltage +5V +12V +3. 3V -12V Ground PS_ON Ground Ground Ground -5V +5V +5V JATXPWR1: ATX Power Connector PU 12 24 1 13 12 P4M800 JATXPWR2: ATX Power Connector By connecting this connector, it will provide +12V to CPU power circuit. PU 3 1 4 2 Pin 1 2 3 4 Assignment +12V +12V Ground Ground JAUDIO1: Front Panel Audio Header This header allows user to connect the front audio output cable with the PC front panel. It will disable the output on back panel audio connectors. Pin 1 2 3 4 5 PU 6 7 8 9 2 14 10 1 13 11 12 13 14 Assignment Mic in/center Ground Mic power/Bass Audio power Right line out/Speaker out Right Right line out/Speaker out Right Reserved Key Left line out/Speaker out Left Left line out/Speaker out Left Right line in/Rear speaker Right Right line in/Rear speaker Right Left line in/Rear speaker Left Left line in/Rear speaker Left 13 P4M800 JSPDIFO1: Digital Audio-out Connector This connector allows user to connect the PCI bracket SPDIF output header. PU Pin 1 2 3 Assignment +5V SPDIF_OUT Ground 3 1 JPANEL1: Front Panel Header This 24-pin connector includes Power-on, Reset, HDD LED, Power LED, Sleep button, speaker and IrDA Connection. It allows user to connect the PC case's front panel switch functions. PU SLP 2 1 PWR_LED On/Off +++- IR 24 23 SPK RST HLED IR Pin 1 3 5 7 9 11 13 15 17 19 21 23 Assignment +5V N/A N/A Speaker HDD LED (+) HDD LED (-) Ground Reset control N/A N/A +5V IRTX Function Speaker Connector Hard drive LED Reset button IrDA Connector Pin 2 4 6 8 10 12 14 16 18 20 22 24 Assignment Sleep control Ground N/A Power LED (+) Power LED (+) Power LED (-) Power button Ground Key Key Ground IRRX Function Sleep button N/A Power LED Power-on button IrDA Connector 14 P4M800 JUSB3/JUSB4: Front USB Headers This motherboard provides 2 USB 2. 0 headers, which allows user to connect additional USB cable on the PC front panel, and also can be connected with internal USB devices, like USB card reader. PU 2 10 JUSB3 JUSB4 1 9 Pin 1 2 3 4 5 6 7 8 9 10 Assignment +5V (fused) +5V (fused) USBUSBUSB+ USB+ Ground Ground Key NC JCMOS1: Clear CMOS Header By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting and the CMOS data, please carefully follow the procedures to avoid damaging the motherboard. PU 1 3 Pin 1-2 Close: Normal Operation (default). 1 3 1 3 Pin 2-3 Close: Clear CMOS data. Clear CMOS Procedures: 1. The BIOS has been recovered and will work properly. 18 P4M800 B. CPU Overheated If the system shutdown automatically after power on system for seconds, that means the CPU protection function has been activated. When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again. After confirmed, please follow steps below to relief the CPU protection function. Power on the system again. 19 P4M800 4. 3 1. TROUBLESHOOTING Probable 1. No power to the system at all Power light don't illuminate, fan inside power supply does not turn 2. Keyboard lights are on, power indicator lights are lit, and hard drive is spinning. Using even pressure on both ends of the DIMM, press down firmly until the module snaps into place. Make sure both ends are securely plugged in; check the drive type in the standard CMOS setup. Re-install applications and data using backup disks. System does not boot from hard disk 1. drive, can be booted from optical drive. 2. System only boots from optical drive. Hard disk can be read and applications can be used but booting from hard disk 2. Screen message says "Invalid Configuration" or "CMOS Failure. " Cannot boot system after installing second hard drive. Review system's equipment. [. . . ] "Verify button": User can click this button and [WarpSpeederTM] will proceed a testing for current frequency. If the testing is ok, then the current frequency will be saved into system registry. After reboot, the [WarpSpeederTM] utility will restore to the hardware default setting or load the verified best and stable frequency according to the Recovery Dialog's setting. Note: Because the testing programs, invoked in Auto-overclock and Verify, include DirectDraw, Direct3D and DirectShow tests, the DirectX 8. 1 or newer runtime library is required. And please make sure your display card's color depth is High color (16 bit) or True color( 24/32 bit ) that is required for Direct3D rendering. d. 5. Hardware Monitor Panel Click the Hardware Monitor button in Main Panel, the button will be highlighted and the Hardware Monitor panel will slide out to left as the following figure. [. . . ]