User manual VIA KLE133 BROCHURE

[. . . ] 1-1 Overview AthlonTM Processors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1- 3 LAN (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1- 3 Serial ATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1- 4 I/O Shield Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] AGP Master 1 WS Write When Enabled, Writes to the AGP (Accelerated Graphics Port) are executed with one wait states. AGP Master 1 WS Read When Enabled, Reads to the AGP (Accelerated Graphics Port) are executed with one wait states. AGP 3. 0 Calibration cycle This item allows you to select AGP 3. 0 Calibration cycle function. Options: Enabled, Disabled. Page 4-10 BIOS CPU & PCI Bus Control Scroll to CPU & PCI Bus Control and press <Enter>. The following screen appears: PCI1/2 Master 0 WS Write When Enabled, Writes to the PCI bus are commanded with zero wait states. PCI Delay Transaction The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. Select Enabled to support compliance with PCI specification version 2. 2. Options: Enabled, Disabled. Page 4-11 BIOS 4-4 Integrated Peripherals Figure 5: Integrated Peripherals Init Display First If two video cards are used (1 AGP and 1 PCI) this specifies which one will be the primary display adapter. Options: Enabled, Disabled, Auto. Page 4-12 BIOS VIA OnChip IDE Device Scroll to VIA Onchip IDE Device and press <Enter>. The following screen appears: IDE DMA transfer access Automatic data transfer between system memory and IDE device with minimum CPU intervention. OnChip IDE Channel0/1 The integrated peripheral controller contains an IDE interface with support for two IDE channels. Options: 5, 10. Page 4-16 BIOS 4-5 Power Management Setup Choose the POWER MANAGEMENT SETUP in the CMOS SETUP UTILITY to display the following screen. This menu allows the user to modify the power management parameters and IRQ signals. In general, these parameters should not be changed unless its absolutely necessary. Figure 6: Power Management ACPI Suspend Type This item allows you to select S1(POS) or S3(STR) function. Power Management Option Use this to select your Power Management selection. User define: Allows user to define PM Timers parameters to control power saving mode. HDD Power Down When enabled and after the set time of system inactivity, the hard disk drive will be powered down while all other devices remain active. Page 4-17 BIOS Suspend Mode enabled and after the set time of system inactivity, all devices except the CPU will be shut off. Video Off Option When enabled, this feature allows the VGA adapter to operate in a power saving mode. Suspend->Off: Monitor blanked when the systems enters the suspend mode. Video Off Method This option allows you to select how the video will be disabled by the power management. The default is V/H Sync + Blank V/H Sync + Blank: DPMS Support: System turns off vertical and horizontal synchronization ports and writes blanks to the video buffer. [. . . ] Click "Auto Lock" to detect S/PDIF input and display its information. Check "Real-time S/PDIF-In monitor" to listen to the S/PDIF IN signal through Line-out connector. This page lets you choose the type of audio source that will appear on the S/PDIF-out connector. Page 6-5 Drivers Installation This board is equipped with Jack Sensing capability. If an audio device is plugged into the wrong connector, a warning message will appear to remind users to check the connection. [. . . ]