User manual VESTAX QFO LE

[. . . ] Follow Instructions-All operating and use instructions should be followed. Attachments-Do not use attachments not recommended by the product manufacturer as they may cause hazards. Water and Moisture-Do not use this product near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like. Accessories-Do not place this product on an unstable cart, stand, tripod, or table. [. . . ] The product may fall, causing serious injury to a child or adult, and serious damage to the appliance. stand, tripod, bracket, or table recommended by the manufacturer, or sold with product. Any mounting of the appliance should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 10. Power sources-This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. Lightning-For added protection of this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the product due to lightning and power-line surges. Overloading-Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. It allows for selection of one of the two inputs connected rear panel. rTALK OVER SWITCH When this switch is depressed, the levels of all sources except MIC muted. When this switch is ON, the master signal is always Adjust TRIM so that MASTER LED METER heard through the right earcup of the headphone. CUE signal will be heard in the left earcup when that input is selected by the CUE SELECT !0INPUT EQ-HI(Equalizer High) SWITCH(!3) . Boosts of +6dB and cuts of monitored simultaneously, thus assisting in beat 24dB are possible at 20kHz. Boosts of +6dB and cuts of 5 24dB are possible at 1kHz. 10 16 15 LINE 5 QFO LE / PROFESSIONAL MIXING CONTROLLER FOR THE CREATIVE DJ / PRODUCER ALLOWS YOU TO CREATE YOUR OWN MUSIC WITH VESTAX'S UNSURPASSED ENGINEERING AND DESIGN. 1 50 MASTER LEVEL L MAX -20 -16 -12 -10 -8 -4 -2 0 +2 +4 +8 +12 dB R +6dB OUTPUT BALANCE +6dB L R 17 18 MASTER CUE SUB MASTER +6dB CUE OUT MASTER OUT 19 20 L CROSS FADER MIN MAX MIN MAX MIN MAX CF ASSIGN PGM 1 PGM 2 CF ASSIGN PGM 3 PGM 4 22 TRANSFORMER TRANSFORMER 12 21 23 !9MASTER OUTPUT LEVEL Adjust the signal level output from MASTER OUT jack on the rear panel. !2INPUT EQ-LOW(Equalizer Low) Auxiliary bass knob. Boosts of +6dB and cuts of 24dB are possible at 80Hz. !3CUE SWITCH Used to send the signal to the monitor section for head phone. @0MASTER CUE SWITCH Used to send the signal to the monitor section for head phone. !4INPUT FADER Used to adjust input level of the various PGM channels. Usually at 7-8. @1CROSS FADER Mixes the signals assigned by CROSSFADER ASSIGN SWITCH (@2) to left side of the crossfader and right side. When the crossfader is in the center position, both left and right signals can be heard. This is a detachable feder for ease of replacement with CF-PCV when it is worn out. !5PEAK LEVEL METER The bar graph level meters indicate the peak L&R output. !6SUB MASTER OUTPUT LEVEL Adjust the signal level output from SUB MATER OUT jack on the rear panel. @2CROSSFADER ASSIGN SWITCH Used to assign the signals from each of the PGM channels to either side of the crossfader or to the master section. !7CUE OUTPUT LEVEL !8MASTER BALANCE Adjust the signal level output from CUE OUT jack on the rear panel. Determines balance between left and right channels. @3TRANSFORMER SWITCH With the crossfeder moved to either right or left, the opposite program can be heard instantly by pressing the opposite transformer button. 6 REAR PANEL 24 28 26 29 31 CAUTION RISK OF ELECTRIC SHOCK. [. . . ] This is a detachable feder for ease of replacement with CF-PCV when it is worn out. !5PEAK LEVEL METER The bar graph level meters indicate the peak L&R output. !6SUB MASTER OUTPUT LEVEL Adjust the signal level output from SUB MATER OUT jack on the rear panel. @2CROSSFADER ASSIGN SWITCH Used to assign the signals from each of the PGM channels to either side of the crossfader or to the master section. !7CUE OUTPUT LEVEL !8MASTER BALANCE Adjust the signal level output from CUE OUT jack on the rear panel. Determines balance between left and right channels. @3TRANSFORMER SWITCH With the crossfeder moved to either right or left, the opposite program can be heard instantly by pressing the opposite transformer button. 6 REAR PANEL 24 28 26 29 31 CAUTION RISK OF ELECTRIC SHOCK. AVIS;RISQUE DE CHOC ELELCTRIQUE -NE PAS OUVRIR. 35 MADE IN CHINA UNDER LICENCE OFVESTAX TOKYO, JAPAN 37 MIC MIC 1 AC 12V 600mA SERIAL NO. MASTER R +4 0 -10(dB) SUB MASTER L CUE OUT PGM 4 LINE 5 LINE 4 INPUT PGM 3 LINE 3 PHONO 3 PGM 2 LINE 2 PHONO 2 PGM 1 LINE 1 PHONO 1 MIC1, 2 EFF LOOP SEND BALANCE OUT LEVEL R L L L L L MIC 2 POWER REC OUT R PIN 1 PIN 2 GND HOT R R R MIC 3 R L GND GND GND RETURN AC IN 12V PIN 3 COLD 25 27 30 32 34 36 @4POWER SWITCH @5AC POWER JACK Connect to the AC-12 adaptor. #1CUE OUT JACK The signal selected by CUE SWITCH and MASTER CUE SWITCH is mono output. It can be sampled by connecting to the input of any sampler without hearing over the P. A. [. . . ]