User manual VESTAX PVT-E2

[. . . ] Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to. Follow Instructions-All operating and use instructions should be followed. Attachments-Do not use attachments not recommended by the product manufacturer as they may cause hazards. Water and Moisture-Do not use this product near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like. [. . . ] Accessories-Do not place this product on an unstable cart, stand, tripod, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the appliance. stand, tripod, bracket, or table recommended by the manufacturer, or sold with product. Any mounting of the appliance should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 10. Power sources-This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. Lightning-For added protection of this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the product due to lightning and power-line surges. The new PVT-E2 features removable flat panel that covers all screws etc. , that will impede fast mixing. New suprior grade crossfader (CF-PCV) fittde to PVT-E2 enebling super smooth operation torether with long life. 3 FUNCTIONS MIC INPUT SECTION PROGRAM INPUT SECTION MASTER SECTION 12 4 PROGRAM INPUT SECTION 5 EQUALIZER (MID 1KHz +6dB -24dB) Adjusts the MID frequeny level of each PGM channel. 1 2 3 4 7 5 6 8 6 EQUALIZER (LOW 80Hz +6dB -24dB) Adjusts the LOW freguency level for each PGM channel. 7 EQ CUT SWITCH ( HI, MID, LOW ) Cuts off the each frequency range by 24dB. The EQUALIZER volume dose not function when this switch is set to "CUT". 8 EFFECT SWITCH Used to send the signal to the external effect processor connected to the effect SEND/RETURN. 9 P. F. L. . SWITCH Used to send the signal from the PGM channel to the monitor section for headphone monitoring. 10 OVERLOAD INDICATOR Lights when input level is over. 9 10 11 INPUT FADER This is a detachable fader for the ease of replacement. Replace with IF-175 when it is worn out. 12 CROSS FADER When the input level of PGM1 and PGM2 are properly set, PGM1 will be heard with the cross fader set to the left side. When the cross fader is set in the center, both programs will be heard. This is detachable fader for the ease of replacement witrh "CF-PCV" when it is worn out. 11 1 INPUT SELECTOR Used to select input (2 line or 1 phono) to be sent to each PGM channel. 2 TRIM CONTROL Adjusts the input level of each channel. Set INPUT FADER to 7-8 position, adjust the TRIM CONTROL so that the sufficient signal is fed without distortion. 3 BALANCE CONTROL Adjusts the stereo balance for each PGM channel. Clockwise rotation from center position increases the volume of R over L channel. A counter clockwise rotation increases the volume of L channel over R. 4 EQUALIZER (HI 10Hz +6dB -24dB) Adjusts the HI frequeny level of each PGM channel. 5 HOW TO CHANGE THE FADER UNIT Driver HOW TO REMOVE THE TOP PANEL 1 Remove each fader knobs and 6 screws which fix the top panel. 2 Remove the top panel. Driver HOW TO CHANGE THE FADER UNIT 1 Remove the screws on the fader panel. [. . . ] Clockwise rotation from center position increases the volume of R over L channel. A counter clockwise rotation increases the volume of L channel over R. 4 EQUALIZER (HI 10Hz +6dB -24dB) Adjusts the HI frequeny level of each PGM channel. 5 HOW TO CHANGE THE FADER UNIT Driver HOW TO REMOVE THE TOP PANEL 1 Remove each fader knobs and 6 screws which fix the top panel. 2 Remove the top panel. Driver HOW TO CHANGE THE FADER UNIT 1 Remove the screws on the fader panel. 3 Carefully remove the multi-cable connector from fader unit. 4 Attach multi-cable connector to new fader unit. 5 Position the fader unit carefully and secure with screws. Insert the multi-cable connector CF-PCV For PMC SERIES ( PMC05ProII, PMC06ProA, etc) Set switch to "PCV" position. PMC CONNECTOR Set switch to "PMC" position 6 MIC INPUT SECTION 13 MIC INPUT JACK(MAIN MIC, MIC1 3) Input jacks for MAIN MIC, MIC1, MIC2 and MIC3. 14 MIC LEVEL Adjusts the input level of MIC1, 2 and 3. 13 15 MIC EQUALIZER(HI, LOW) Adjusts the HI and LOW frequency level of MIC1, 2 and 3. 16 EFFECT SWITCH Used to send the signal to the external effect processor connected to the effect SEND/RETURN. 14 17 P . F. L. [. . . ]