User manual VESTAX PMC-CX

[. . . ] Carts and Stands-The appliance should be used only with a cart stand that is recommended by manufacturer. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. FEATURES The PMC-CX was built to give Carl Cox what he always wanted. A solid, reliable, high quality mixer, that has enough features to allow him to give 110% during every performance, every time. Specifically the PMC-CX includes a number of features that will definitely give you a lot more creative freedom whilst "in the mix". [. . . ] When switch is on, an indicator lights up. r PGM BALANCE VOLUME Adjusts the stereo balance for each PGM channel. Can be used !4 INPUT LEVEL VOLUME for adjusting the unbalanced stereo image. Typically this from center position increases the volume of R over L channel. This fader is user A counter clockwise rotation increases the volume of L replaceable and may be changed easily by following this channel over R. y PGM ISOLATOR MID Adjusts the MID frequency level of each PGM. u PGM ISOLATOR LOW Adjusts the LOW frequency level of each PGM. HOW TO CHANGE THE FADER UNIT MIC / LINE SECTION @9 SUB MIC LEVEL VOLUME Adjusts the input level of the SUB MIC input. REAR PANEL #0 MAIN MIC / SUB LINE SELECTOR Selects between MAIN MIC and SUB LINE input. #1 MIC / LINE EQ VOLUME Adjusts the HI and LOW frequencies for the signal chosen by MAIN MIC / SUB LINE SELECTOR. #2 MIC / LINE LEVEL VOLUME Adjusts the input level of the MAIN MIC or SUB LINE input. #3 MIC / LINE CUE SWITCH Sends the signal from the MIC or LINE channel to the monitor section for headphone monitoring. When switch is on, an indicator lights up. #8 MAIN/SUB MIC JACK [MAIN MIC: XLR JACK (BALANCED), SUB MIC: PHONE JACK (UNBALANCED)] Input jack for MIC. $7 MASTER OUT 1/2 JACK [1/4' PHONE JACK (UNBALANCED), XLR JACK (BALANCED] Connect to the input on a power amplifier. This mixer has two sets of MASTER OUT jacks so that the each output level can be set separately. Therefore, the MASTER OUT can be used for main output or sub output IE. One for the main area and the other for entrance. #9 LINE INPUT JACK MONITOR SECTION #4 SPLIT / STEREO SELECTOR When this switch is set to "SPLIT", the master signal is always heard through the right ear-cup of the headphone. The signal selected by each CUE SWITCH will be heard in the left ear-cup. This enables both programs to be monitored simultaneously, thus assisting in beat mixing. When this switch is set to "STEREO" no master output is heard in the headphones, and only the signal selected by each CUE SWITCH will be heard in both ear-cups. [LINE: RCA PIN JACK, SUB LINE: 1/4' PHONE JACK (UNBALANCED)] Input connectors for line level equipment such as CD players, CD-R/RW players, MD players, tape decks, DVD players, DAT and VTR etc. $8 MASTER OUT LEVEL SELECT SWITCH [-10/0dB] Select the attenuation level for the BOOTH OUT. $0 PHONO INPUT JACK $9 MASTER LOOP SEND JACK Input jacks for turntables. (Delay, Reverb, etc. ) $1 GND TERMINAL #5 HEADPHONE EQ VOLUME Adjusts the HI and LOW frequencies for Headphone monitoring. #6 HEADPHONE LEVEL VOLUME Adjusts the headphone monitor level. Connect this terminal to the ground lead of the turntable. $2 INPUT LEVEL SELECT SWITCH[-10/0dB] Select the attenuation level for the input. $3 BOOTH OUT JACK [1/4' PHONE JACK (UNBALANCED), XLR JACK %2 AC IN JACK (BALANCED)] Connect the Vestax AC-20 , AC adaptor. This signal is identical to the HEADPHONE OUT signal. $4 BOOTH OUT LEVEL SELECT SWITCH Select the attenuation level for the BOOTH OUT. #7 PHONES JACK Use this jack to connect headphones. Headphones with an impedance of 8ohm to 600ohm can be used on this unit. *For best sound quality Vestax recommends using Headphones with 150ohm impedance. $5 MIC MONITOR IN/OUT SWITCH Select whether the signal connected to MAIN/SUB MIC is mixed with the signal outputted from MASTER OUT1/2. $6 REC OUT JACK Connects to the input jack of a recording device IE, tape recorder, MD, DAT, etc. [. . . ] This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 10. Power sources-This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. [. . . ]