User manual VESTAX PMC-55

[. . . ] Damage Requiring Service-Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. If the product dose not operate normally by following the operating instructions. [. . . ] Can be used for adjusting the unbalanced stereo image caused by strong Anti-Skating setting. Clockwise rotation from center position increase volume of R over L channel. Counter clockwise rotation increase volume of L channel over R. 1 L R INPUT LINE 1 2 PHONO 1 LINE 2 6 4 EQ CUT SWITCH Press this switch to bypass EQ section. TRIM +3 7 EQ (HI, MID, LOW) Adjusts the HI, MID and LOW frequencies for each PGM channel. HI 8kHz -24dB~ +6dB Shelving type MID 500Hz -24dB~ +6dB Peaking type LOW 80Hz -24dB~+6dB Shelving type 3 MIN 0 BAL -3 -8 -13 (dB) MAX 5 L R EQ CUT 6 EQ HI -24dB MID +6dB (0dB) 7 -24dB LOW +6dB (0dB) 8 AUX ASSIGN SWITCH Used when sending signal to external effect processor connected to AUX SEND/RETURN (42). -24dB +6dB (0dB) OUT AUX 8 PRE POST 9 MASTER 1 MASTER 2 IN IN MASTER OUT ASSIGN 1, 2 Used to send the signal from each program to either MASTER OUT 1 or 2 (43). ASSIGN A MASTER B 11 CUE 10 CROSSFADER ASSIGN Used to send the signal from each program to either the crossfader (A or B) or the master directory. A for left side of the crossfader, B for right side. 10 9 8 7 6 5 4 3 2 1 0 12 11 CUE ASSIGN Used to send the signal from each program to monitor section for headphones monitoring. This allows for sending signal to external sampling unit connected to CUE OUT. 1 LINE IN 2, 4, 6, 8 (RCA) Used for line level input. Line level musical instruments with stereo outputs such as rhythm machine or sampler are also good for LINE IN. This is particularly useful for "visiting" equipment. 12 INPUT FADER Used to adjust the Input level of each program. Replace with IF50 when It is worn out. 2 INPUT SELECTOR Used to select the input (two LINE or one PHONO) to be sent to each PGM channel. HOW TO REPLACE THE INPUT FADER Remove four screws which hold the fader unit panel. Take the unit out with the panel Remove a knob and two screws which hold the fader unit. Replace the knob and the fader unit to the panel and fix it with screws. Replace the fader unit panel and tighten the screws. 3 INPUT LEVEL METER The LED level meters indicate the input signal level of each PGM channel. 4 GAIN CONTROL Adjusts the input level of each channel. Set INPUT FADER (12) to 7-8 position, adjust GAIN so that INPUT LEVEL METER(3) shows about 0dB. 5 55/E 00. 9. 12 4:44 PM 12 CROSSFADER SECTION TRANSFORMER TRANSFORMER CF MODE A B 14 13 13 15 HOW TO REPLACE THE CROSS FADER Remove a knob and four screws which hold the fader unit. [. . . ] And remove front panel. BOOST CANCEL SWITCH Each EQ volume has boost cancel switch. When boost cancel switch is on, equalizer range changes - 24 +6dB to - 24 0dB EQ boost is canceled. -24dB +6dB -24dB 0dB TRIM LEVEL SELECT SWITCH Each trim volume has level select switch. you can select range of trim from -20, -10, and 0dB. 12 55/E 00. 9. 12 4:44 PM 2 SPECIFICATIONS PHONO LINE MIC AUX RTN MASTER LOOP RTN PGM I/O RTN MASTER OUT UNBAL. [. . . ]