User manual VESTAX PMC-37PRO

[. . . ] Accessories-Do not place this product on an unstable cart, stand, tripod, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the appliance. stand, tripod, bracket, or table recommended by the manufacturer, or sold with product. Any mounting of the appliance should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. [. . . ] MODE PGM 1 PGM 2 PGM 3 CUE MONITOR MONITOR SELECT LEVEL LEVEL LEVEL MASTER AUX 1 AUX 2 SPLIT STEREO MONITOR LEVEL MIN MAX PHONES CROSS FADER A B PHONES CROSSFADER SECTION 5 PROGRAM SECTION the volume of R over L channel. A counter clockwise rotation increases the volume of L channel over R. tISOLATOR ON/OFF SWITCH When set to "OFF", a full range signal is transmitted regardless of the position of any isolator controls. Each frequency range can be boosted up to +6dB when this knob is pushed fully up. uDRY-FILTER MIX FADER Allows control of the signal balance between dry and effect (FILTER) sound. When you rotate clockwise, the point is moved towards higher frequency. oAUX ASSIGN SWITCH This switch enables the signal from each program to be sent to EFFECT SEND JACK ($1). Different signal routes can be selected by moving this switch to the following different positions; PRE: The signal before the input fader (after the EQ) will be sent to AUX output. POST: The signal after the input and crossfader will be sent to AUX output. ASSIGN SWITCH Used to send the signal from each program to either side of the crossfader (A or B) or direct to the master. "A" for left side of the crossfader, "B" for right side. !1CUE SWITCH Used to send the signal from each program to the monitor section for headphone monitoring. This is a detachable fader for ease of replacement, replace with IF37PCV when it is worn out. If you wish to use the fader unit with slide stroke distance of 45mm, you can replace with the Vestax "IF-05PCV". See "HOW TO CHANGE THE FADER UNIT". 1 2 3 4 5 6 INPUT 2 PHONO 2 LINE 2 INPUT 3 PHONO 3 LINE 3 PGM 2 INPUT ASSIGN 1 2 3 GAIN 4 BAL MIN MAX L ON OFF R ISOLATOR LOW +6dB MID HI +6dB -OOdB -OOdB FILTER DRY SWEEP 7 8 9 A FILTER MIN MAX AUX 1 PRE OFF POST AUX 2 C. F. ASSIGN B MASTER CUE 10 11 OFF ON PGM 2 LEVEL 12 qINPUT SELECT SWITCH Used to select input source from either PHONO or LINE. wINPUT ASSIGN SWITCH Used to assign the signal from each input, INPUT1 to INPUT4, to be sent to each PGM. Set INPUT FADER (!2) to 7-8 position and adjust the GAIN CONTROL so that a sufficient signal is fed without distortion. Clockwise rotation from center position increases 6 CROSS FADER SECTION C. F. Counter-clockwise rotation gives a gentle crossfade, good for long running mixes. Clockwise rotation gives a steep crossfade, suitable for scratching and cutting. 1 2 3 L E V E L B POSITION POSITION POSITION A !3CROSS FADER 3) 2 Mixes the signal assigned by C. F. ASSIGN SWITCH f i g - A CROSS FADER CURVE (!0) to A side of the crossfader and B side. [. . . ] rLoosen 2 screws with marking on IF-05PCV, and remove the fader panel from fader (VR) assembly. tInstall the fader panel of IF-37PCV to the fader unit (VR assembly) of IF-05PCV. CURVE SELECT SWITCH 10 CF37P CV 7 1 5 3 1 2 (for IF-05PCV) fig-E fig-F IF-05PCV INPUT FADER CURVE B L E V E L D A FADER POSITION fig-G fig-H CONNECTION DIAGRAM [example] SPEAKER AMPLIFIER SPEAKER AMP. VESTAX PT-X1000A CHANNEL A CHANNEL B PROTECT B. T. L POWER PEAK PEAK POWER MINI MAX MINI MAX INPUT INPUT ON / OFF INPUT CD, MD player, TAPE DECK etc :connect to LINE input jack of PMC-37Pro CD PLAYER e. g. [. . . ]