User manual VESTAX PMC-250

[. . . ] Accessories-Do not place this product on an unstable cart, stand, tripod, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the appliance. stand, tripod, bracket, or table recommended by the manufacturer, or sold with product. [. . . ] Carts and Stands-The appliance should be used only with a cart stand that is recommended by manufacturer. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. FEATURES 1. The input fader can boost / cut and eliminate individual frequency be replaced with a rotary control for House ranges for active mixing. One Phono and two Line inputs are provided on smooth and dynamic frequency cut-off without each program channel PGM1, PGM2 . The I/O panel can be placed on either the rear or and a Mic input are also provided. This feature enables the PMC-250 to be used on the table or in a rack without any extra space for the leads. 3 FUNCTIONS PROGRAM SECTION PGM 1 INPUT LINE 1 PHONO 1 LINE 2 MASTER SECTION PGM 2 INPUT LINE 3 TRIM TRIM LINE 4 PRO FESSIONAL MIXING CONTROLLER +6 +3 +2 +1 0 -1 -2 -4 -7 -10 -20 -30 POWER -30 -20 -10 -7 -4 -2 -1 0 +1 +2 +3 +6 MIN MAX PHONO 2 PEAK ISOLATOR IN PEAK IN PEAK IN PEAK ISOLATOR IN MIN MAX PEAK IN PEAK IN Lch PGM 1 Rch AUX METER SELECT 10 9 8 7 6 5 4 3 2 1 0 PGM 2 CUT CUT CUT LOW 0 MID 0 HI 0 INPUT + 4dB - + 4dB FILTER + 4dB MIC LEVEL 10 9 8 7 6 5 4 3 2 1 0 CUT CUT CUT MASTER MIN MAX PGM LOW 0 MID 0 HI 0 MASTER BOOTH OUT MIN MAX MIN MAX - + 4dB - + 4dB PHONES + 4dB MONITOR CUE SELECTOR ON STEREO CUE LEVEL PGM 1 LEVEL PGM 2 LEVEL 1 MIN MAX MIN MAX 2 OFF 1 AUX 2 MIN MAX MIC SECTION MONITOR SECTION PROGRAM SECTION PGM 1 INPUT LINE 1 PHONO 1 LINE 2 TRIM 2 MIN MAX 1 PEAK ISOLATOR PEAK IN PEAK IN 3 IN CUT CUT CUT LOW 0 9 MID 0 8 HI 0 7 - + 4dB - + 4dB - + 4dB 10 10 9 8 7 6 5 4 3 2 1 0 6 5 4 PGM 1 LEVEL q INPUT SELECT (Input Select Switch) Used to select input to be sent to each PGM t MID (Isolator MID) channel. The w TRIM (Trim Control Volume) level is flat when this knob is set at 12 o'clock. For Mid frequency range is boosted up to +4dB proper adjustment, please set the INPUT when this knob is rotated clockwise. When the FADER to Maximum position then adjust TRIM knob is rotated counter-clockwise, mid so that the INPUT LEVEL METER shows frequency range is cut off up to infinity level. example, it can be used to emphasise or cut off the vocals or guitars. e PEAK Turns on when the signal of HI, MID, LOW y LOW (Isolator LOW) range hits the peak. The r HI (Isolator HI) level is flat when this knob is set at 12 o'clock. The Low frequency range is boosted up to +4dB level is flat when this knob is set at 12 o'clock. When the High frequency range is boosted up to +4dB knob is rotated counter-clockwise, low when this knob is rotated clockwise. [. . . ] 3 Carefully remove the multi-cable connector Top panel from fader unit. 4 Attach multi-cable connector to new fader unit. 5 Position the fader unit carefully and secure with screws. Inputfader unit Crossfader unit Note Use a plus driver fitting screw. Caution: When you change any parts, do not loose the screws with marking. CF-PCV For PMC SERIES ( PMC05ProII, PMC06ProA, etc) Insert the multi-cable connector Set switch to "PCV" position. PMC CONNECTOR 8 Set switch to "PMC" position HOW TO CHANGE THE JACK PANEL POSITION The I/O jack panel of the PMC-250 can be placed either on the top or back side of the unit. [. . . ]