User manual VESTAX PMC-08PRO

[. . . ] Attachments-Do not use attachments not recommended by the product manufacturer as they may cause hazards. Water and Moisture-Do not use this product near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like. Accessories-Do not place this product on an unstable cart, stand, tripod, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the appliance. [. . . ] stand, tripod, bracket, or table recommended by the manufacturer, or sold with product. Any mounting of the appliance should follow the manufacturer's instructions, and sholud use a mounting accessory recommended by the manufacturer. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 10. Power sources-This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. Lightning-For added protection for this product during lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the product due to lightning and power-line surges. Overloading-Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. A powerful 3 band EQ with +6/-24dB range is provided along with the instant out switch on each band. More sensitve and drastic control can be achieved for Techno/Trans mixing. 3 FUNCTIONS MIC INPUT SECTION PROGRAM INPUT SECTION MASTER SECTION 4 PROGRAM INPUT SECTION 1 2 3 4 6 EQUALIZER (LOW 80Hz +6dB -24dB, Shelving type) Adjusts the LOW freguency level for each PGM channel. 7 EQ CUT SWITCH ( HI, MID, LOW ) Cuts off the each frequency range by 24dB. The EQUALIZER volume dose not function when this switch is set to "CUT". 8 EFFECT SWITCH Used to send the signal to the external effect processor connected to the effect SEND/RETURN. 9 P. F. L. . SWITCH Used to send the signal from the PGM channel to the monitor section for headphone monitoring. 7 5 6 10 11 OVERLOAD INDICATOR Lights when input level is over. INPUT FADER This is a detachable fader for the ease of replacement. Replace with IF-17 when it is worn out. 8 9 10 HOW TO REPLACE THE FADER 11 Remove four screws which is holding the fader panel. Place the fader unit and tighten the screws. 1 INPUT SELECTOR Used to select input (2 line or 1 phono) to be sent to each PGM channel. 2 TRIM CONTROL Adjusts the input level of each channel. Set INPUT FADER to 7-8 position, adjust the TRIM CONTROL so that the sufficient signal is fed without distortion. + + 3 BALANCE CONTROL Adjusts the stereo balance for each PGM channel. Clockwise rotation from center position increases the volume of R over L channel. A counter clockwise rotation increases the volume of L channel over R. Remove four 4 sarews Remove the multi cable connector + + 4 5 EQUALIZER (HI 10Hz +6dB -24dB, Shelving type) Adjusts the HI frequeny level of each PGM channel. EQUALIZER (MID 1KHz +6dB -24dB, Peaking type) Adjusts the MID frequeny level of each PGM channel. 5 12 CROSS FADER When the input level of PGM1 and PGM2 are properly set, PGM1 will be heard with the cross fader set to the left side. [. . . ] Clockwise rotation from center position increases the volume of R over L channel. A counter clockwise rotation increases the volume of L channel over R. Remove four 4 sarews Remove the multi cable connector + + 4 5 EQUALIZER (HI 10Hz +6dB -24dB, Shelving type) Adjusts the HI frequeny level of each PGM channel. EQUALIZER (MID 1KHz +6dB -24dB, Peaking type) Adjusts the MID frequeny level of each PGM channel. 5 12 CROSS FADER When the input level of PGM1 and PGM2 are properly set, PGM1 will be heard with the cross fader set to the left side. When the cross fader is set in the center, both programs will be heard. This is detachable fader for the ease of replacement witrh CF-R US when it is worn out. 12 Remove the multi cable connector + + Remove four sarews 4 + + MIC INPUT SECTION 13 MIC INPUT JACK(MAIN MIC, MIC1 3) Input jacks for MAIN MIC, MIC1, MIC2 and MIC3. 14 MIC LEVEL Adjusts the input level of MIC1, 2 and 3. 13 15 MIC EQUALIZER(HI, LOW) Adjusts the HI and LOW frequency level of MIC1, 2 and 3. 16 EFFECT SWITCH Used to send the signal to the external effect processor connected to the effect SEND/RETURN. 14 17 P . F. L. [. . . ]