User manual VESTAX PMC-07PRO

[. . . ] This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. Power sources-This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. Lightning-For added protection for this product during lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. [. . . ] Overloading-Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. Object and Liquid Entry-Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Servicing-Do not attempt to service product yourself as opening or removing covers may expose you to dangerrous voltage or other hazards. Damage Requiring Service-Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. If the product dose not operate normally by following the operating instructions. Adjust only those controls that are coverd by the operating instructions as an improper adjustment of other, controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. When the product exhibits a distinct change in perfromance-this indicates need for service. 16. Replacement Parts-When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characterristics as the original parts. Unauthorized substitutions may result in fire, electric shock or other hazards. Safety Check-Upon completion of any service or repairs to product, ask the service technician to perfrom sefety checks to determine that the product is in proper operating condition. Carts and Stands-The appliance should be used only with a cart stand that is recommended by manufacturer. Reverse mode is indicated in LED section. @4 CF REVERSE SWITCH Reverses the action of the crossfader by switching PGM1 and 2. Reverse mode is indicated in LED section. L E V E L @5 IF CURVE SELECT VOLUME Adjusts the input fader curve for steep or gentle slope. POSITION POSITION POSITION Rotate clockwise this volume, C. F curve changes like a chart ( 1 2 3) fig. B CROSS FADER CURVE 3 L E V E L @7 MINI HEADPHONE JACK [ 2 1 3. 5 ] Connect headphones with 1/8" mini headphone plug. @8 HEADPHONE JACK [ 6. 3 ] Connect headphones with a standard 1/4" stereo plug. POSITION Rotate clockwise this volume, I. F curve changes like a chart ( 1 2 3) f i g . A INPUT FADER CURVE 6 REAR PANEL SECTION 31 33 35 37 WARNING;SHOCK HAZARD-DO NOT OPEN. AVIS;RISQUE DE CHOC ELELCTRIQUE -NE PAS OUVRIR. 39 CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN MASTER SERIAL NO. FRONT PROFESSIONAL QUADRAPHONIC DJ MIXER SUB MASTER SESSION IN PMC-07ProISP AUX SEND PHONO IN 1 R L MADE IN JAPAN POWER REAR 2 R L GND AC 12V R L R L R L AUX RTN 29 30 @9 POWER SWITCH 32 34 36 38 40 #3 SUB MASTER OUT JACK-FRONT [1/4 inch PHONE JACK unbalance] Sub output jack for front left and front right speaker zone. Unbalanced connectors at -4dBm for monitoring etc. Power for mixer, on status indicated by POWER LED(!6) on top panel; should be turned on after all connections are made. Note As a general rule for protection, the amp should be turned on last and turned off first. #4 SUB MASTER OUT JACK-REAR [1/4 inch PHONE JACK unbalance] Sub output jack for rear left and rear right speaker zone. Unbalanced connectors at -4dBm for monitoring etc. #0 AC POWER JACK Connect AC ADAPTOR (AC-12A) in here before switching on power. #5 SESSION IN JACK-FRONT [1/4 inch PHONE JACK] Allows front 1/4 inch chain connection with multiple PMC-07ProISP mixers. Note UNAUTHORIZED POWER ADAPTORS MAY CAUSE HARM TO UNIT. #6 SESSION IN JACK-REAR [ 1/4 inch PHONE JACK ] Allows rear 1/4 inch chain connection with multiple PMC-07ProISP mixers. #1 MASTER OUT JACK-FRONT [1/4 inch TRS balanced] Main output jacks for front left and front right speaker zones. Connect to power amp or crossover. Note See "CHAIN CONNECTION DIAGRAM" of page 10. #2 MASTER OUT JACK-REAR [1/4 inch TRS balanced] #7 AUX SEND JACK [1/4 inch PHONE JACK ] Connect to the input of external effects. (delay, Main output jacks for rear left and rear right reverb etc. ) speaker zones. Connect to power amp or #8 AUX RETURN JACK [1/4 inch PHONE JACK] crossover. Note (delay, reverb etc. ) These connectors are Tip=hot, Ring=cold, #9 PHONO INPUT JACK [ RCA JACK ] Sleeve=ground. [. . . ] This input for turntables with MM cartridges HOT COLD GND only. $0 GROUND(GND) TERMINAL The grounding lugs for turntables. Ground for phono circuit necessary to avoid hum. fig. C T. R. S JACK 7 HOW TO CHANGE THE FADER UNIT Note Use a plus driver fitting screw. Caution: When you change any parts, do not loose the screws with marking. Top panel Driver Knob HOW TO REMOVE THE TOP PANEL q Remove each fader knobs and 4 screws which fix the top panel. w Remove the top panel. Main panel HOW TO CHANGE THE FADER UNIT q Remove the two screws on the fader panel. [. . . ]