User manual VESTAX PMC-06PRO A

[. . . ] This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. Power sources-This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. 11. Lightning-For added protection for this product during lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. [. . . ] Overloading-Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. Object and Liquid Entry-Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Servicing-Do not attempt to service product yourself as opening or removing covers may expose you to dangerrous voltage or other hazards. Damage Requiring Service-Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. If the product does not operate normally by following the operating instructions. Adjust only those controls that are coverd by the operating instructions as an improper adjustment of other, controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. When the product exhibits a distinct change in perfromance-this indicates need for service. 16. Carts and Stands-The appliance should be used required, be sure the service technician has used only with a cart stand that is recommended by replacement parts specified by the manufacturer manufacturer. An appliance and cart combination should be fire, electric shock or other hazards. Quick stops, excessive force, and uneven surfaces may cause the appliance 17. Safety Check-Upon completion of any service or and cart combination to overturn. !7 EFFECT SEND ON/OFF SWITCH This selector switch can also be used to perform for This switch is used to select the PGM to be sent to TRANSFORMER SCRATCH. To change the operational direction of this !8 MONITOR LEVEL switch remove the top panel and make the necessary the top panel. Adjusts the headphone monitor level. Used to adjust the input level of each PGM channel. fader curve can be changed using a switch located on the unit @0 MONITOR SELECT SWITCH itself. Ensure that you This switch is used to select the signal sent to the monitor replace with an IF-05PCV when it is worn out. When set to CUE the signal heard is determined comprehensive instructions please refer to the "HOW TO by which PGM is being sent to the master and the location CHANGE THE FADER UNIT" section of this user guide. When set to MASTER you !3 INPUT LEVEL METER will hear the master signal in the monitor section. The LED level meters indicate the signal level of each !9 CF MONITOR FRONT PANEL @1 PHONE JACK Connect the headphones with the impedance of 8ohm to 600ohm. @3 EFFECT SEND JACK Connect to the input of the external effects. (Delay, Reverb etc) @2 EFFECT RECEIVE JACK Connect to the output of the external effects. REAR PANEL @4 SUB MIC LEVEL Adjusts the input level from SUB MIC IN. connected, the signal from the turntable is fed to the respective PGM when the Phono Input is selected. @5 MAIN/SUB MIC JACK Input jack for MAIN/SUB MIC. @8 GROUND TERMINAL Connect this terminal to the ground lead of the turntables. @6 LINE INPUT JACK @7 PHONO INPUT JACK These jacks are used to connect line level output @9 POWER JACK devices to the PMC-05proIII. level of -10dB to 0db, such as CD player, MD #0 LINE OUT players, tape decks, DAT players etc. may be The PMC-05ProIII has two pairs of Line Out jacks connected to these jacks. [. . . ] may be The PMC-05ProIII has two pairs of Line Out jacks connected to these jacks. The signal from these sending the same output signal to an external devices is then fed to the respective PGM when Line amplification device. These jacks are used to connect turntables equipped with moving magnet (MM) type cartridges. Once #1 POWER SWITCH Use to turn power on. HOW TO CHANGE THE FADER UNIT q Remove the fader knobs. [. . . ]