User manual VESTAX PCV-180

[. . . ] This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 3. Power sources-This product should be appliance and in the operating instructions operated only from the type of power should be adhered to. Follow Instructions-All operating and use to your home, consult your appliance dealer instructions should be followed. Use a damp cloth for product during a lightning storm, or when it cleaning. [. . . ] is left unattended and unused for long periods of time, unplug it from the wall 6. This will prevent damage to the recommended by the product manufacturer product due to lightning and power-line as they may cause hazards. Overloading-Do not overload wall outlets near water-for example, near a bath tub, and extension cords as this can result in a wash bowl, kitchen sink, or laundry tub, in a risk of fire or electric shock. Object and Liquid Entry-Never push objects of any kind into this product through 8. Accessories-Do not place this product on an openings as they may touch dangerous unstable cart, stand, tripod, or table. The voltage points or short-out parts that could product may fall, causing serious injury to a result in a fire or electric shock. Never spill child or adult, and serious damage to the liquid of any kind on the product. Servicing-Do not attempt to service product the manufacturer, or sold with product. Any yourself as opening or removing covers mounting of the appliance should follow the may expose you to dangerous voltage or manufacturer's instructions, and should use other hazards. When the cross fader is set in the center, both programs will be heard. This is a detachable fader for the ease of replacement with "CF-RUS" "CF-R" or "CF-PCV" when it is worn out. i PHONES JACK Use this jack to connect the head phones. o MASTER LEVEL Adjusts the signal level output from the LINE OUT jack on the rear panel. !0 MASTER BALANCE Adjusts the signal balance of the left and right side of the outputs from the LINE OUT jack on the rear panel. !2 MONITOR SELECT FADER When the monitor levels of PGM1 and PGM2 are properly set, PGM1 will be monitored in the headphone with the fader set to the left side and PGM2 will be monitored in the head phone with the fader set to the rigth side. When the fader is set in the center, both programs will be monitored in the head phone. !3 MIC LEVEL Adjusts the input level from all microphone inputs. 5 How to change the fader unit. HOW TO REMOVE THE TOP PANEL 1 Remove all fader knobs and the 4screws which driver fix the top panel. (see fig. A) 2 Remove the top panel. HOW TO CHANGE THE FADER UNIT 1 Remove the screws on the fader panel. (see fig. B) 2 Remove the fader unit from position in mixer. 3 Carefully remove the multi-cable connector from fader unit. (see fig. C) 4 Attach multi-cable connector to new fader unit. 5 Position the fader unit carefully and secure with screws. Remove the multi-cable connector from fader unit. fig. A driver Remove four scews. 4 fig. C You can replace the CF unit with "CF-RUS", "CF-R" or "CF-PCV". HOW TO REPLACE THE CF UNIT WITH "CF-PCV" When the fader unit is replaced, please see fig. C. [. . . ] 3 Carefully remove the multi-cable connector from fader unit. (see fig. C) 4 Attach multi-cable connector to new fader unit. 5 Position the fader unit carefully and secure with screws. Remove the multi-cable connector from fader unit. fig. A driver Remove four scews. 4 fig. C You can replace the CF unit with "CF-RUS", "CF-R" or "CF-PCV". HOW TO REPLACE THE CF UNIT WITH "CF-PCV" When the fader unit is replaced, please see fig. C. Place the fader unit in the proper position and fix it with two screws. (fig. D- b ) CAUTION There is a swith for "CF-PCV" unit. When "CFPCV" unit is installed, set the switch to "PCV" mode. fig. B CAUTION When the fader unit is replaced, do not loosen the screws with marking. fig. D CF-RUS or CF-R CF-PCV 6 REAR PANEL 19 18 17 RISK OF ELECTRIC SHOCK. [. . . ]