User manual VESTAX MX-1

[. . . ] VESTAX observes the manufacturing coubtry s regulations. F E AT U R E S Three band isolator switch kills each frequency range completely in quick action. Pre / Post selectable AUX send swich enables various effect processing. The effect signal can be controlled by a dedicated return level control knob, the signal can be also monitored by headphone when "return" is selected by cue button. Three phono and 6 line inputs are provided to meet the new mixing style with various input source. [. . . ] User replaceable 60 m/m input faders and 45 m/m cross fader make "on sight service" very easy. Optional input rotary volume can be replaced with the fader for "House" application. This allows DJs to uae hand carried DAT or MD player mixing with installed equipment. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTl0N TO REDUCE THE RlSK OF ELECTRlC SHOCK DO NOT REMOVE COVER OR BACK NO USER-SERVICEABLE PARTS INSIDE REFER SERVlCING T0 QUALIFIED SERVlCE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to consitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING T0 REDUCE THE RISK 0F FIRE 0R ELECTRlC SHOCK THIS APPLIANCE T0 RAIN 0R M0ISTURE CAUTION DO NOT EXPOSE TO PREVENT ELECTRIC SHOCK, MATCH BLADE OF PLUG TO WIDE SLOT FULLY INSERT ATTENTION P0UR EVITER LES CH0CS ELECTRIQUES INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESP0NDANTE DE LA PRISE ET P0USSER JUSQU AU F0ND IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUTIONS WARNING : When using electric products, basic precautlons nhould always be followed, including the following : 8. Do not use this product near water - for example, near a from the outlet when left unused for a long period of time. Care should be taken so that objects do not fall and liquids are bathtub, washbowl, kitchen sink, in a wet basemant, or near a swimming pool, or the like. The product should be services by qualified service personnel when ; recommended by the manufacturer. Objects have fallen, or liquid has been spilled into the and hrsdphones or speakers, may be capable of producing product ; or sound levels that could cause permanent hearing loss. The product has been exposed to rain ; or operate for a long period of time at a high volume level or at a D. The product does not appear to operate normally or level that is uncomfortable. Do not attempt to service the product beyond that described in with its proper ventilation. The product should be located away from heat sources such as the use - maintenance instructions. EFFECT SWITCH MASTER CUE Used when sending signal to the external effect +8 +8 processor connected to the effect SEND/RETURN. CUE SWITCH +3 +3 Used to send the signal from the mic channel to the +1 +1 monitor section for head phone monitoring. 0 0 -1 -1 -3 -5 -7 -10 -15 POWER L R MIC 10 MIC-1 MIC-1 MIC-2 11 MIN MAX MIC-2 MASTER SECTION MIN MAX 16 -3 -5 -7 -10 -15 POWER EQ HI 12 -16dB +16dB LOW -16dB +16dB EFFECT 13 OFF POST CUE 14 OFF ON 15. MASTER OUT LEVEL METER The LED level meters indicate the signal level of the line out. CUE LEVEL METER The LED level meters indicate the signal level of PGM input selected by CUE SWITCH. EFFECT SEND LEVEL Used to adjust the output level from EFFECT SEND JACK. EFFECT RETURN LEVEL Used to adjust the input revel from the EFFECT RETURN JACK. EFFECT CUE SWITCH Used to send the signal from EFFECT RETURN JACK to the monitor section for headphone monitoring. MASTER BALANCE VOLUME Adjusts the signal balance of left to the right side of the outputs from the OUTPUT jack on the rear panel. MASTER LEVEL VOLUME Adjust the signal level output from the OUT PUT jack on the rear panel. SPLIT CUE SWITCH When this switch is ON, the master signal is always heard through the right earcup of the headphone. [. . . ] SPLIT CUE SWITCH When this switch is ON, the master signal is always heard through the right earcup of the headphone. The CUE signal will be heard in the left earcup when that input is selected by the CUE SWITCH (5, 14). This enables both programas to be monitored simultaneusly, thus assisting in beat mixing. HEAD PHONE JACK Use this jack to connect the headphones the inpodance 8ohm to 600ohm can be used, 150ohm is recommended. L R 15 EFFECT SEND 17 MIN MAX RETURN 18 MIN MAX 19 CUE OFF ON MASTER BAL 20 L R LEVEL 21 MIN MAX MONITOR SPLIT CUE ON OFF 22 PHONES LEVEL 23 MIN MAX PHONES IN 24 ISOLATOR SECTION 25, HI SWITCH Allows cutting off the sound of treble range. [. . . ]