User manual VESTAX GFE-1

[. . . ] This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. Power sources-This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. [. . . ] Quick stops, excessive technician to restore the product to its force, and uneven surfaces may cause the normal operation. When the product exhibits a distinct change in performance this indicates need for service. Replacement Parts-When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the WARRANTY PLEASE NOTE THAT INPUT FADERS AND CROSSFADERS ARE NOT COVERED BY THE NORMAL WARRANTY AS THEY ARE MOVING PARTS WHICH ARE SUBJECT TO WEAR AND TEAR, AND IN MANY CASES THEY ARE USER REPLACEABLE. EACH DISTRIBUTOR HAS THEIR OWN WARRANTY SYSTEM IN ACCORDANCE WITH THE COUNTRY OR STATE REGULATIONS OR LAWS. VESTAX OBSERVES THE MANUFACTURING COUNTRY'S REGULATION. 4 FEATURES Matrix input assign system allows instant selection of multiple sound sources for any input channel. Incredibly, for the first time, one turntable could be assigned to every program channel. 3 band isolator (slide volume control) on each program channel for extreme mixing techniques. Sweep filter control cuts or boosts a narrow frequency band giving DJs a new creative tool to add flanging type effects to their performance. High quality VCA circuitry provides optimum S/N, warm fat sound and broadcast quality audio. 2 effect loops with PRE/POST switches on each channel for ultimate control of effect processing. 2 microphone inputs with 2 band EQ and effect send/return. FUNCTIONS TOP PANEL MIC AUX SECTION PROGRAM SECTION MASTER MONITOR SECTION PROFESSIONAL MIXING CONTROLLER INPUT SELECTOR INPUT 1 INPUT 2 PHONO 2 LINE 2 INPUT 3 PHONO 3 LINE 3 INPUT 4 PHONO 4 LINE 4 MIC MAIN MIC PHONO 1 LINE 1 LEVEL +8 +5 +3 PGM 1 MIN MAX PGM 2 INPUT ASSIGN 1 2 INPUT ASSIGN 1 2 3 BAL GAIN 4 PGM 3 INPUT ASSIGN 1 2 3 GAIN 4 SUB MIC 3 BAL GAIN +1 4 MIN MAX BAL +0 -1 -3 -5 EQ HI MIN MAX MIN MAX L ON OFF LOW MID HI +6dB R MIN MAX L ON OFF R MIN MAX L ON OFF R -7 -10 -15 CUE L R LOW MIN OFF MAX ISOLATOR ISOLATOR ISOLATOR MIC SEND LOW MID HI +6dB LOW MID HI POWER AUX 1 AUX 2 AUX 1 SEND FILTER MIN MAX DRY -OOdB -OOdB MASTER BAL FILTER FILTER SWEEP DRY SWEEP DRY SWEEP L R RCV MASTER LEVEL MIN MAX FILTER MIN MAX FILTER MIN MAX FILTER MIN MAX AUX 2 SEND AUX 1 PRE OFF MIN MAX POST AUX 2 AUX 1 PRE OFF POST AUX 2 AUX 1 PRE OFF POST AUX 2 MIN MAX SUB MASTER LEVEL RCV C. F. ASSIGN SWITCH f i g - A CROSS FADER CURVE (!0) to A side of the crossfader and B side. When the crossfader is set in the center position, both A and B can be heard. This is a detachable fader for !5CUE LEVEL METER The LED bar level meters indicate the signal level of ease of replacement with CF-37PCV when it is worn PGM input selected by CUE SWITCH (!1). !6MASTER OUT LEVEL METER MASTER-MONITOR SECTION The LED bar level meters indicate the L and R outputs. !8MASTER BALANCE VOLUME 15 Adjusts the signal balance of the L to R side of outputs from MASTER OUTPUT JACK (#9) on the 16 rear panel. !9MASTER LEVEL VOLUME 17 Adjusts the signal level outputs from MASTER OUTPUT JACK (#9) on the rear panel. MASTER @0SUB-MASTER LEVEL VOLUME Adjusts the signal level outputs from SUB-MASTER 18 OUTPUT JACK ($0) on the rear panel. @1MONITOR SELECT SWITCH 19 Used to select the cue monitor for PGM1 4 (selected by CUE position), MASTER out and effect receive (AUX 1 or AUX 2). 20 @2MONITOR STYLE SELECT SWITCH When this switch is set to "SPLIT", the master signal is always heard through the right ear-cup of the MONITOR headphones. The signal selected by MONITOR SELECT SWITCH (@1) will be heard in the left ear-cup. 21 This enables both programs to be monitored simultaneously, thus assisting in beat mixing. [. . . ] (See fig-C) wRemove the top panel. HOW TO CHANGE THE FADER UNIT qRemove the screws on the fader panel. (See fig-D) fig-C Caution When you change any parts, do not loosen the screws with marking. wRemove the fader unit from position in mixer. (See fig-D) eCarefully remove the multi-cable connector from fader unit. fig-D HOW TO REPLACE THE INPUT FADER UNIT WITH "IF-05PCV" CHANGE TO "IF-05PCV" qRemove the input fader unit "IF-37PCV". [. . . ]