User manual VESTAX GE-62A

[. . . ] This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 10. Power sources-This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. Lightning-For added protection for this product during lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. [. . . ] Overloading-Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. Object and Liquid Entry-Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Servicing-Do not attempt to service product yourself as opening or removing covers may expose you to dangerrous voltage or other hazards. Damage Requiring Service-Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. If the product dose not operate normally by following the operating instructions. Adjust only those controls that are coverd by the operating instructions as an improper adjustment of other, controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. When the product exhibits a distinct change in perfromance-this indicates need for service. 16. Replacement Parts-When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characterristics as the original parts. Unauthorized substitutions may result in fire, electric shock or other hazards. Safety Check-Upon completion of any service or repairs to product, ask the service technician to perfrom sefety checks to determine that the product is in proper operating condition. Carts and Stands-The appliance should be used only with a cart stand that is recommended by manufacturer. The monitor PGM sent the headphone is controlled through the MONITOR MODE SELECT SWITCH. When set to "STEREO" no master output is heard in the headphones, and only the signal selected by MONITOR SELECT SWITCH will be heard in both ear-cups. @4 MONITOR MODE LED This LED will be illuminated when the MONITOR MODE SELECT SWITCH@3 is on. @5 PHONES JACK Use this jack to connect headphones. Headphones with an impedance of 8ohm to 600ohm can be used on this unit. *For best sound quality Vestax recommends using Headphones with 150ohm impedance. @1 MONITOR EQ (HI/LOW) Adjusts the HI and LOW frequencies for Headphone monitoring. @2 MONITOR LEVEL Adjusts the headphone monitor level. MASTER SECTION #1 METER ASSIGN SWITCH Use this switch to select either MASTER OUT 1 or 2 to be shown in the MASTER LEVEL METER #0. #2 POWER LED This LED will be illuminated when the POWER SWITCH %4 is on. #3 AUX SEND LEVEL Adjusts the output level sent to an external effects unit connected to the AUX SEND JACK $9 on the rear panel. When the crossfader is used, this signal is taken after the crossfader but before the master fader. This makes a variety of techniques possible, such as the application of echo to a cut out in which the crossfader would be used. #4 AUX RCV LEVEL Adjusts the input level from an external effect unit connected to the AUX RCV JACK %0 on the rear panel. #5 AUX CUE ON/OFF SWITCH Sends the signal of external effects unit connected to the AUX SEND JACK to the MONITOR section for headphone monitoring. #6 AUX CUE LED This LED will be illuminated when the AUX CUE SWITCH#5 is on. #7 AUX RCV LEVEL METER This LED bar level meter indicates the level of the AUX RCV JACK signal. @6 MASTER BALANCE 1&2 #8 BOOTH OUT EQ (HI/LOW) @7 MASTER LEVEL 1&2 Adjusts the HI and LOW frequencies for the Adjusts the signal balance of the L to R side of the BOOTH OUT. outputs from MASTER OUT 1&2 JACKS %2 on the #9 BOOTH OUT LEVEL rear panel. Adjusts the signal level outputs from MASTER OUT 1&2 JACKS on the rear panel. $0 MUTE SWITCH This switch mutes the signal being sent to BOOTH OUT. @8 MASTER 1&2 CUE SWITCH Used to send the signal from the MASTER OUT 1&2 to the monitor section for headphone monitoring. $1 MUTE LED This LED will be illuminated when the MUTE SWITCH $0 is on. @9 MASTER 1&2 CUE LED This LED is illuminated when the MASTER 1&2 CUE SWITCH @8 is on. $2MASTER 1&2 & BOOTH OUTPUT LEVEL SELECTOR (ATTENUATION). Located under the top panel, this switch adjusts the output level for Master 1&2 in addition to the Booth out put level. The GE-62A is pre-set to a 0dB output level but may be changed to -10dB. #0 MASTER LEVEL METER This LED bar level meter indicates the L and R outputs. REAR PANEL $3 MIC1 INPUT JACK Input jack for MIC. MIC1: PHONE JACK (UNBALANCED) MIC2: XLR JACK (BALANCED) %1 REC OUT JACK Connects to the input jack of any recording device IE, tape recorder, MD, DAT, etc. The output level of this jack is fixed and does not change with the MASTER LEVEL. $4 EFFECT LOOP JACK TIP: SEND OUT RING: RETURN INPUT SLEEVE: EARTH Connects to the input of an external effects device. %2MASTER OUT1&2(1/4" PHONE JACK (UNBALANCED), XLR JACK(BALANCED) Connect to the input on a power amplifier. [. . . ] The output level of this jack is fixed and does not change with the MASTER LEVEL. $4 EFFECT LOOP JACK TIP: SEND OUT RING: RETURN INPUT SLEEVE: EARTH Connects to the input of an external effects device. %2MASTER OUT1&2(1/4" PHONE JACK (UNBALANCED), XLR JACK(BALANCED) Connect to the input on a power amplifier. This mixer has two sets of MASTER OUT jacks so that the each output level can be set separately. Therefore, the MASTER OUT can be used for main output or sub output IE. One for the main area and the other for entrance. %3 BOOTH OUT(1/4" PHONE JACK (UNBALANCED), XLR JACK(BALANCED) Connects to the DJ booth monitors. $5 INPUT LEVEL SELECT SWITCH (0dB/-10dB) Selects the attenuation level for any input signal. $6 LINE INPUT RCA JACK Input connectors for line level equipment such as CD players, MD players, tape decks, DAT and/or VTR etc. $7 PHONO INPUT RCA JACK Input jacks for turntables. [. . . ]