User manual VESTAX CDX-35

[. . . ] HOW TO CONNECT A PLUG IMPORTANT The wires in the mains lead are coloured in This apparatus is fitted with an approved moulded 13 accordance with the following code: Amp plug. To change a fuse in this type of plug BLUE-"NEUTRAL"("N") proceed as follows: BROWN-"LIVE"(L") 1. Remove fuse cover and fuse. 1. The BLUE wire must be connected to the terminal 2. Fix new fuse which should be a BS1362 5A. 2. The BROWN wire must be connected to the If the fitted plug is not suitable for your sockel terminal which is marked with the letter "L" or outlets, It should be cut off and an appropriate plug coloured RED. 3. Do not connect either wires to the earth terminal in this should have a value of 5A. [. . . ] Safety Check-Upon completion of any service or repairs to product, ask the service technician to perfrom sefety checks to determine that the product is in proper operating condition. Carts and Stands-The appliance should be used only with a cart stand that is recommended by manufacturer. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. FEATURES Analog-touch cueing system Thanks to a large buffer memory and ultra-fast DSP, the cue point can be searched for with a jog wheel, just like an analog player. The sound is produced as the wheel is spun, back and forth, slow or fast, just like cueing vinyl. The new way of CD cueing, point focus an alternative way of cueing is also provided. The CDX-35 produces a short loop of sound around the laser pick up, just like any other CD player. The difference with the CDX-35 is that the length can be adjusted from 0. 013 to 3 seconds. Therefore, exactly one beat, half bar or full bar can be monitored in a loop and the loop can be moved around. This advanced monitor system makes the CD cueing no longer a pain but fun. Up to 20 seconds of sound can be looped instantaneously by pressing buttons. Dedicated start, stop and re-loop / exit buttons allow the DJs to create 4 8 Master tempo / master key and play around with the loop on the fly. Reverse play In addition to regular pitch control, the CDX-35 offers two advanced tempo and key controls. Thanks to the DSP technology, the tempo can be changed +10% without changing the key, and the key can be changed +-20% without changing the tempo. The special technique, which was only possible with a special analog turntable is now available by just touching a button. The CDX-35 also offers more playability with the total of four cue / memory points. This feature makes the CDX-35 almost endless multi-sampling machine. Three plus one instant cue positions Seamless loop BEFORE USE Notes on the Compact Disc (CD) The surface which is glossy like a ralnbow is the front side of the CD, and the surface where the label information is printed is the back side. Unlike conventional analog disk turntables, the CD player reads information from the disc by applying laser beam, in place of a stylus, on the front surface. Consequently, the performance of CD discs will not degrade after repeated use like conventional analog disks. Handle the CD disc carefully so as not to damage the front surface. To maintain the CD disc flawless, do not place it in the following locations. In a place subject to direct sunlight or near a heat source such as a room heater. b, The search dial will temporarily bend the pitch of the music up to +/- 10% if the song is already playing by rotating the dial clockwise to speed up or counterclockwise to slow down. The amount of pitch change is determined by the speed of rotation. MONITOR KEY When the monitor button is pressed during the PAUSE mode , a short loop sound of the paused position is played back for monitoring. Then exact position for the next start can be searched and set by using the SEARCH DIAL. PITCH CONTROLLER The pitch can be changed up to +/- 10% by moving sliding fader. POINT FOCUS KEY Used for changing time of monitor sound. KEY CONTROL CUE MEMORY Press the cue memory button. The key can be change up to +/- 1 octave by rotating volume. MASTER TEMPO Press the MASTER TEMPO button. [. . . ] Loop play begins automatically (between the loop-in and loop-out points). back S E During the loop play, press the "START" button. The player's pickup will return to set the loop in point and continues loop play. LOOP [2] CHANGE THE LOOP END POINT A S B [3] CANCEL /RETURN LOOP PLAY During loop play, press the "RELOOP/EXIT" button. When playback reaches the loop out point, Playback continues without returning to the loop in point. After LOOP A adjust end pointby pressing A or B button B canceling loop play, press the "RELOOP/EXIT" button during playback. [. . . ]