User manual VELODYNE VX-11 DATASHEET 1

[. . . ] To prevent fire or shock hazard, do not expose this equipment to rain or moisture. To avoid electrical shock, do not open speaker enclosure or amp chassis cover. Please refer all service questions to your authorized Velodyne dealer. Prior to Installation Please unpack the system carefully. Record the serial number in the space provided on page 17 of this manual for future reference. PRODUCT FEATURES DSP-Controlled 4 selectable preset modes for customized listening Automatic 7-band room equalizer with microphone included Night-mode setting Mute control Woofer - 8" (6. 5" piston diameter) subwoofer with 2. 5" high-temp voice coil and 107 ounce magnet/204 ounce motor structure (SPL-800 Ultra) - 10" (8" piston diameter) subwoofer with 3" voice coil and 162 ounce magnet/ 346 ounce motor structure (SPL-1000 Ultra) - 12" (9. 7" piston diameter) subwoofer with 3" voice coil and 162 ounce magnet/ 346 ounce motor structure (SPL-1200 Ultra) · Built-in 2400 watts Dynamic/1200 watts RMS high efficiency Class D amplifier · Adjustable (40 to 135 Hz) low-pass crossover (defeatable) · Line-level (RCA) inputs and outputs · Speaker-level inputs with five way binding post connections · Signal sensing auto turn on/off (defeatable) · Variable volume control · Selectable phase control (0, 90, 180 or 270 degrees) · Overall frequency response of 16-240 Hz (SPL-800 Ultra), 13-240 Hz (SPL-1000 Ultra), 13-240 Hz (SPL-1200 Ultra), · Magnetically shielded for video use (SPL-1000 Ultra and SPL-1200 Ultra) · Multiple staggered low-pass crossovers; 12 dB/octave initial, 48 dB/octave ultimate · Driver Displacement Control circuit to prevent over excursion and amp clipping · Blue level indicator LED · High-excursion EPDM rubber surround · Oversized spider for linearity at high excursion · Hand-rubbed black lacquer or cherry veneer cabinet · · · · · · . www. velodyne. com SPL-Ultra User's Manual 1 Prepare for Installation Your new Velodyne subwoofer provides for a number of installation options. [. . . ] The sub will remain in this mode until the POWER button is pressed again. (2) LED Numeric Display This LED supplies information on volume, crossover, presets, and other information. (3) Volume Control These buttons allow you to balance the output from the subwoofer to the main speakers in your system. The volume should be set to achieve similar volume level of both the main speakers and subwoofer. The upper button increases the subwoofer level and the lower button decreases it. WARNING: Some manufacturers preset their receivers with the Sub-Out (A. K. A. It is very important to verify that your receiver Sub-Out channel is set to the same output level as your front right and left channels. Refer to your receiver manual for the individual channel level adjustment procedure. If your receiver Sub-Out channel is set too low, the subwoofer may appear to have a weak output, it may sound noisy or distorted, and the Auto On/Off feature may not operate properly. (4) Mic Input Connect the supplied microphone for the Auto-EQ feature to this mini-jack input. . www. velodyne. com SPL-Ultra User's Manual 6 R e a r Pa n e l C o n n e c t i o n s Figure 2. SPL-Ultra Rear Panel Connections Figure 2 shows the connections on the rear panel of the SPL-Ultra. RE . www. velodyne. com SPL-Ultra User's Manual 7 Following are brief descriptions of the connections described in Figure 2. Note: If you are not using an external crossover, you should use the built-in crossover for the best performance. When using a single RCA sub out from the processor, connect to the "L" - LFE input on the subwoofer, or for more signal, use a "Y" connector and feed the signal into both "R" and "L" inputs. Interconnect Cables When installing your new Velodyne subwoofer using the line-level connections, you should always use shielded phono cables. There are many decent cables available today, most any of which will work perfectly well. We do recommend that you keep the length of cable as short as possible to avoid any potential noise problems. When using speaker level connections, use a quality speaker cable that mates well with the connectors (at least 18-gauge). Be very careful to avoid any loose or frayed strands that could result in a short, causing a dangerous condition and possible damage to your unit. Extremely large gauge wire may not properly fit in the binding posts, resulting in a poor connection and possible short circuits. . www. velodyne. com USAGE SPL-Ultra User's Manual 10 Usage This section addresses day-to-day usage of your SPL-Ultra subwoofer. Remote Control Figure 3 shows the remote control, enabling you to easily choose whatever listening mode you desire. NOTE: The SPL-Ultra remote can be attached magnetically to the back of the subwoofer in the upper left hand corner. Figure 3. Remote Control POWER This button forces your SPL-Ultra unit into standby mode. The unit will remain in this mode until the POWER button is pressed again. power down) the unit, turn off the power switch on the back panel. MUTE . This button mutes the subwoofer. [. . . ] During normal conditions, the subwoofer may be left on continuously without any problems. If you plan to leave the unit unused for an extended period of time, we recommend that you turn off the subwoofer by the master power switch on the rear panel. T roubleshooting and Service Before seeking service for your amplifier or subwoofer, please re-check all systems. Have all controls on the amplifier (volume, crossover, phase, etc. ) been properly set?If the unit has been running at high levels, one of the protection circuits may be engaged. [. . . ]