User manual VELODYNE VA 1012X

[. . . ] While it is recommended that the subwoofer be placed on the same plane as the satellite speakers, room and system conditions often dictate otherwise. Keep in mind that frequency response and output level can be drastically influenced by placement, depending on the acoustic properties of the listening room. Typically, the optimum location for a subwoofer is tucked away in a corner of your listening room. This location will usually offer the greatest output levels and optimum low frequency extension. [. . . ] This control should be set to achieve similar output level from both the main speakers and subwoofer when listening to music. A good starting point for the volume control is 3 or 4 dots from minimum. Low-pass Crossover - 40 to 120 Hz All inputs sum the left and right channels together, with the resulting signal passing through an adjustable low-pass crossover before being amplified. The crossover control allows you to adjust the upper limit of the subwoofer's frequency response from 40 to 120 Hz. The subwoofer's response will begin rolling off above the frequency you set this control to. You should set the crossover frequency to obtain a smooth and seamless transition from the subwoofer to the main speakers in your system. If your main speakers are smaller units with limited low frequency output, you may wish to choose a higher frequency (such as 100 -120 Hz) than you would with larger speakers which have greater low frequency output. With larger speakers, you might start with this control set lower, such as 80 Hz. A bypass switch is also provided if you wish to use an external crossover. If you are not using an external crossover, we recommend that you use the one provided within the unit for optimum performance! Phase Adjustment - 0°/180° This control allows you to "reverse" the phase of the subwoofer's output signal 180° to correct for any possible mismatch and resulting cancellation between the subwoofer and your main speakers/amplifier. Then move the switch from one position to the other and listen for a change in low frequency output. The correct position will have a greater amount of apparent low frequency output. Crossover Switch - INTERNAL X-OVER/SUBWOOFER DIRECT This switch allows the internal crossover circuitry to be removed from the signal path. This will make the unit turn on at lower signal levels. www. velodyne. com SPLi Series User's Manual 5 LINE-LEVEL CONNECTION - OPTION B Figure 2 shows connection from a pre-amplifier's main outputs to the left and right inputs of your Velodyne subwoofer. You will also need to connect a second pair of RCA cables from the outputs on the back of your subwoofer to the inputs on the back of your amplifier. When the subwoofer is installed in this fashion, your satellite speakers will be crossed over at 80 Hz which removes the lower bass frequencies from your external amplifier and speakers, enabling them to do a better job reproducing the higher frequencies. By utilizing this method, you will have a bi-amplified system, gaining improved power and headroom for your system. This installation method is not as common as the method described in Figure 1. (Cables needed: 2 stereo pair of RCA cables. ) NOTE: SPL-800i is identical in features and layout to the SPL-1000i shown. . Figure 2. Installation Using Stereo Line-Level Inputs www. velodyne. com SPLi Series User's Manual 6 Speaker-Level Connections Figure 3 shows an easy way to connect your Velodyne subwoofer directly to your receiver or integrated amplifier, if it lacks line-level outputs. You may also connect your satellites directly to your receiver or amplifier along with the subwoofer. Your receiver or amplifier will not notice the additional load of the subwoofer due to the high input impedance. NOTE: SPL-800i is identical in features and layout to the SPL-1000i shown. Figure 3. To avoid damage to your main amplifier, be sure to maintain correct polarity when making all connections. Be sure that all connections are tight, and that there are no loose strands or frayed wires. www. velodyne. com SPLi Series User's Manual 7 Interconnect Cables When installing your new Velodyne subwoofer using the line level connections, you should always use shielded phono cables. [. . . ] ("VELODYNE") warrants all electronics for a period of three years, drivers for a period of five years, and full range speakers for a period of five years. All VELODYNE products have a warranty from the date of purchase against defects in materials and workmanship subject to the following conditions: 1. VELODYNE is not responsible for defects which result from the use of an amplifier or controller other than the one originally supplied with the unit (subwoofer) or defects which result from modifications or repairs made by any component of the system by anyone other than a VELODYNE factory authorized service representative. This warranty is void if any repairs or service covered by the terms of this warranty are made to any component of the system by anyone other than a VELODYNE factory authorized service representative. [. . . ]