User manual VELODYNE SC-600 IF-IC DATASHEET

[. . . ] Read and follow the instructions below to ensure safe and proper system operation. To prevent fire or shock hazard, do not expose this equipment to rain or moisture. To avoid electrical shock, do not open the speaker enclosure or the amp chassis cover. Please refer all service questions to your authorized Velodyne dealer. Prior to Installation Please unpack the system carefully. [. . . ] Only connect ONE subwoofer to the red/black pair of subwoofer output terminals - DO NOT connect multiple subwoofers to the terminals in any configuration. To avoid damage to your SC-600 IF-IC IF-IC amp and subwoofer, be sure to maintain correct polarity when making all speaker connections; red (positive) to red, and black (negative) to black. Be sure that all connections are tight, and that there are no loose strands or frayed wires. (18) Power Cord Adapter Connect the detachable power plug to this male interface connection. The detachable cord allows for easy replacement should the original become damaged. (20) Main Power Switch Press the POWER switch to the ON position to activate the amplifier. If the unit is to be left unused for an extended period of time, move this switch to the OFF position to prolong the life of the amplifier. . www. velodyne. com SC-600 IF-IC IF-IC Amplifier User's Manual 7 R e a r Pa n e l C o n n e c t i o n s -- D e ta i l e d E x p l a n a t i o n The SC-600 IF-IC IF-IC amplifier is equipped with both speaker-level and line-level inputs. To do this, depress BOTH the Crossover UP and indicating that the Crossover DOWN buttons simultaneously. To reactivate the low-pass crossover, simply push the crossover UP or crossover DOWN buttons. -- A WORD ABOUT YOUR HOME THEATER RECEIVER'S CROSSOVER AND THE SC-600 IF-IC IF-IC AMPLIFIER'S CROSSOVER Your Velodyne SC-600 IF-IC IF-IC amplifier is designed to operate using the full range audio signal for input when using the built-in crossover. Many home theater processors/receivers have a "subwoofer out" jack that performs this same function and are designed to be used with a powered subwoofer. . www. velodyne. com SC-600 IF-IC IF-IC Amplifier User's Manual 8 In these installations, you may want to bypass the crossover in either the processor or the Velodyne SC-600 IF-IC IF-IC amplifier as described above. If you choose to do this you should stagger the frequencies, (i. e. , 120 Hz subwoofer, 80 Hz processor) for best results. You don't need to do anything else - the model to be controlled is automatically stored in the SC-600 IF-IC IF-IC amp's memory. To exit model selection mode, use the main power switch on the back panel to power down and power up the unit. You should see the model you selected for two seconds on the LED display before the display reverts to the volume. Note: The SC-600 IF-IC IF-IC amplifier can control only one subwoofer at a time, either the SC-600 IF-IC IF-IC IW or SC-600 IF-IC IF-IC IF/IC. . www. velodyne. com SC-600 IF-IC IF-IC Amplifier User's Manual 10 Usage This section addresses EQ setup and day-to-day usage of your SC-600 IF-IC IF-IC amplifier. Remote Control The features of the SC-600 IF-IC IF-IC remote control are listed below. · POWER -- This button forces your SC-600 IF-IC IF-IC amplifier unit into standby mode. The power LED turns amber, the numeric LED shuts off, and the amplifier puts out no power. The unit will remain in this mode until the POWER button is pressed again. Note: The master power switch on rear panel must be on in order for the front power button to function. To unmute the subwoofer, press the MUTE button again and the original volume setting shows on the LED. Figure 5: SC-600 IF-IC IF-IC Remote. · EQ -- This button automatically EQs the subwoofer using a 5-band internal graphic equalizer. To use this feature, first plug the supplied microphone into the Mic-In jack on the front panel of the amplifier and place the mic in your preferred listening position. The subwoofer emits 12 "sweep tones" that cover the frequencies between 20 and 150 Hz. [. . . ] Preset Preset Preset Preset Preset Preset Preset Preset 1: 2: 3: 4: 4: 3: 2: 1: Movies R&B ­ Rock Jazz ­ Classical Games Games Jazz ­ Classical R&B ­ Rock Movies When you press the presets in the above order, the numeric LED will display "P3" indicating that you have restored defaults. The unit's volume is reset to level 30 out of 80. C a r e o f yo u r A m p l i f i e r a n d S u b w o o f e r Do not use any harsh detergents or chemicals to clean the SC-600 IF-IC IF-IC chassis or the subwoofer cabinet. Abrasives, detergents, or cleaning solutions will damage the finish on the SC-600 IF-IC IF-IC chassis or the subwoofer cabinet. During normal conditions, the amplifier may be left on continuously without any problems. [. . . ]