User manual VDO CYCLECOMPUTING C15

[. . . ] Accurately position the spoke magnet and the sensor first, then tighten the cable ties. 3. Mounting the spoke magnet Distance between magnet and sensor should be approx. 1-5 mm. 2 In case this distance is not achievable in the current positioning, slide the sensor and the magnet on the fork or spoke accordingly. GB C 15 1-5mm 1-5mm LOCK 4. Twist-Click mounting of computer onto holder UNLOCK The Twist-Click mounting has been exclusively developed for the new line of VDO CYTEC computers. [. . . ] Before resetting to zero, make sure that TCNT information is called into display. without TCNT data being displayed probably resets your TRP-RID-AVS-MAX data to zero. 8 10. Manual stop-watch STP Your VDO CYTEC C 15 features a manual stop-watch. With information STP being displayed, you may operate your stop-watch with the SS-button. GB C 15 Watch out: Pressing the MODE 2 button for 5 sec. without STP data being displayed resets your TRP-AVS-RID-MAX data to zero. SS START/STOP SS press when STP is displayed = starting the stop-watch SS press again = interrupt the stop-watch SS press again = stop watch continues 11. Using this function, as you pass the finish line "freezes" your screen and further impulses are not processed. For triathletes, road racers and for interval-exercise the FREEZE-function provides precise data, i. e. , when passing the finish line, distance, time and average speed values that are being stored during use. 9 GB C 15 Activating the FREEZE-function The FREEZE-function can be activated from any information displayed by simultaneously pressing MODE 1 and MODE 2 buttons for 0. 1 sec. Having activated the FREEZE-function, the letters FRE show up in the upper LCD-segment. Your computer does not process any further impulses, only the clock CLK keeps going. Interrogating information in FREEZE-function Any information can be accessed when you are in FREEZE-mode. Deactivating of FREEZE-function - returning to normal modes The FREEZE-function is deactivated by simultaneously pressing MODE 1 and MODE 2 buttons for 0. 1 sec. The computer will revert back to normal mode again and speed impulses will be processed. Comparison of current and average speed Your VDO CYTEC C 15 compares your current speed with your average speed. The outcome of this comparison can be seen in your display by the use of symbols. No matter which information is currently displayed, this data keeps you updated on the relation of your current speed and your average speed. MODE 1 +MODE 2 to aktivate to deactivate Your current speed is faster than your average speed. Accuracy +/- 1 KMH/MPH 10 You are currently riding as fast as your average speed. Accuracy +/- 1 KMH/MPH Your current speed is slower than your average speed. Set-up mode Your VDO CYTEC C 15 features the following set-up procedures wheelsize 1 = WS1 wheelsize 2 = WS2 clock = CLK odometers = ODO1, ODO2 Trip Counter=TCNT set-up starts out of TRP in display set-up starts out of TRP in display set-up starts out of CLK in display set-up starts out of ODO1, ODO2 in display set up starts out of TCNT in display GB C 15 No matter which set-up mode is used for your VDO CYTEC , the procedure is the same. You can start the set-up mode for a certain display by pressing the MODE 1 button for 5 sec. Once the set-up mode is activated, MODE 1 and MODE 2 buttons are covered with following instructions: MODE1 MODE2 changing from one enter display to the next enter display selection of figure to be entered, changing from KMH to MPH mode 14. Selecting the wheelsize Your VDO CYTEC C 15 can work with two different wheelsizes (WS1 or WS2), i. e. one wheelsize for your road bike the other one for your mountain bike. [. . . ] In case the computer is not properly functioning after a battery change, push the AC-button (Auto Clear) on the rear side of the computer to reset. Troubleshooting This chart outlines possible malfunctions, their causes and solutions. after battery change) speed display does not appear possible cause computer software is not running smoothly check for proper distance between sensor and magnet cable from sensor to computer broken computerhead is incorrectly twisted on handlebar holder no wheelsize entered battery in computer empty temperatures below 5° C (40° F) dull display readout 18 solutions press AC-button at the rear of computer head readjusting distance between sensor and magnet check cable and replace if necessary place computerhead on handlebar holder and twist until detent (CLICK) enter your wheelsize check battery power and replace it if necessary back in normal temperatures, display picks up working correctly display fades or disappears 22. Warranty GB We warrant VDO CYTEC models (sensor, computer head and handlebar holder) to the original purchaser for five years from date of purchase against defects in material and workmanship. [. . . ]