User manual VDO CYCLECOMPUTING C10WL

[. . . ] The sender should be mounted on the same side of the fork as the holder is on the handlebar. Accurately position the spoke magnet and the sender first, then tighten the cable ties. The distance between transmitter (sender) and computer head must not exceed 24 inches (60 cm). Sender range is technically limited in accordance with German telecommunication law. 3. [. . . ] Step 4: By pressing MODE1 key you proceed to the next number, which you can change by pressing MODE 2 key. Step 5: Once you have entered the last number for your TCNT, exit set-up mode by pressing MODE 1 key for 3 sec. . Watch out: When you exit set-up without having completed entering your data, the computer may well work with faulty values leading to misinformation in your display. Press MODE 2 5sec. Reset Reset TCNT to zero The second trip counter TCNT is reset to zero by pressing MODE 2 key for 5 sec. Before resetting to zero, make sure that TCNT information is called into display. without TCNT data being displayed probably resets your TRP-RID-AVS-MAX data to zero. 8 10. Manual stop-watch STP Your VDO CYTEC C 10 WL features a manual stop-watch. With information STP being displayed, you may operate your stop-watch with the MODE 2 -button. GB C 10 WL Watch out: Pressing the MODE 2 button for 5 sec. without STP data being displayed resets your TRP-AVS-RID-MAX data to zero. MODE 2 START/STOP Press MODE 2 5sec. Reset MODE 2 MODE 2 MODE 2 press when STP is displayed = starting the stop-watch press again = interrupt the stop-watch press again = stop watch continues 9 11. Comparison of current and average speed GB Your VDO CYTEC C 10 WL compares your current speed with your average speed. The outcome of this comparison can C be seen in your display by the use of symbols. No matter which information is currently displayed, this data keeps you 10 updated on the relation of your current speed and your average speed. Accuracy +/- 1 KMH/MPH You are currently riding as fast as your average speed. Accuracy +/- 1 KMH/MPH Your current speed is slower than your average speed. Set-up mode Your VDO CYTEC C 10 WL features the following set-up procedures wheelsize 1 = WS1 wheelsize 2 = WS2 clock = CLK odometers = ODO Trip Counter=TCNT set-up starts out of TRP in display set-up starts out of TRP in display set-up starts out of CLK in display set-up starts out of ODO in display set-up starts out of TCNT in display No matter which set-up mode is used for your VDO CYTEC , the procedure is the same. You can start the set-up mode for a certain display by pressing the MODE 1 button for 5 sec. Once the set-up mode is activated, MODE 1 and MODE 2 buttons are covered with following instructions: MODE1 MODE2 10 changing from one enter display to the next enter display selection of figure to be entered, changing from KMH to MPH mode 13. Selecting the wheelsize Your VDO CYTEC C 10 WL can work with two different wheelsizes (WS1 or WS2), i. e. one wheelsize for your road bike the other one for your mountain bike. When using the respective bike you can just switch to the proper wheelsize. Wheelsize is only selectable if any of the following information is displayed: AVS-RID-STP-MAX The currently active wheelsize is indicated in the display by WS 1 or WS 2. [. . . ] Troubleshooting GB C 10 WL Hg This chart outlines possible malfunctions, their causes and solutions. after battery change) speed display does not appear possible cause computer software is not running smoothly check for proper distance between sensor and magnet sender battery emptycheck battery computerhead is incorrectly twisted on handlebar holder no wheelsize entered sender is too distant from computerhead battery in computer empty temperatures below 5° C (40° F) dull display readout solutions press AC-button at the rear of computer head readjusting distance between sensor and magnet power and replace if necessary. place computerhead on handlebar holder and twist until detent (CLICK) enter your wheelsize mount sender closer to computerhead check battery power and replace it if necessary back in normal temperatures, display picks up working correctly display fades or disappears 17 GB 20. Warranty We warrant VDO CYTEC models (sensor, computer head and handlebar holder) to the original purchaser for five years C 10 from date of purchase against defects in material and workmanship. [. . . ]