User manual VAX 6131

[. . . ] It opens the weave of the fabric and agitates the dirt more, to release it easily and quickly. To replicate the movement of hand washing Dyson's engineers designed two aligned drums and engineered them to rotate in opposite directions at the same time. Instead of revolving in the old single pattern of `drop and flop', the clothes are much more active, moving in an infinitely variable dance, to flex the fabric and open the weave to the detergent. Because the Contrarotator releases dirt more effectively, it can wash clothes cleaner. TM User instructions Registration Registering your Dyson Contrarotator TM 3 01 Important safety notes Do not: · stack tumble dryers or other appliances on top of the machine. [. . . ] · the water pressure should be between 0. 4 and 5 bar. Installation Cold only water supply · If there is no hot water supply, attach the cold and hot pipes to the machine as normal. Then, attach both hoses to a Y piece connector (available as a separate accessory, see rear page for Helpline telephone number) and finally connect the Y connector to the cold inlet tap. 5 03 European conformity information This product has been tested and found to be in conformity with the following European Directives: 73/23/EEC Low Voltage (safety) Directive. When all of the instructions on the previous pages have been completed, the machine can be installed into its operating position using the Rollerjack handle, see section TM 4 01. · Do not tighten the plastic hose connections with a spanner. · Do not connect to a mixer tap. · Once all connections have been made, turn on the tap(s) to check that there are no leaks. Electrical installation · Thread the drainage hose through the hose hook and adjust the protruding end to a distance of 30mm. The hose hook has a small retention hole that can be used to secure the hose assembly in position. Hot and cold water supply · Attach the blue hose to the cold inlet tap and the red hose to the hot inlet tap. Drainage hose hook 30mm Drainage hose Warning: This appliance must be earthed · Any electrical work required to install the washing machine should be carried out by a Dyson trained installer or qualified electrician. · Before using your machine, check that the plug and sockets match, and check that the voltage in your home corresponds to that indicated on the rating plate. · The machine should be plugged into a switchable, earthed socket that is easily accessible after installation. · If the supply cord or plug is damaged disconnect the appliance from the socket outlet immediately. The supply cord must only be replaced by Dyson or its appointed agent, as Stand pipe When installed into a standpipe or under sink connection, ensure that the water outlet end of the drainage hose is no lower than 450mm from ground level. Default settings will be set for temperature, spin and dirt level which are safe for that fabric type. 4 Cancel your wash cycle Press and hold down to cancel a programme at any time. The machine will stop and drain all the water and the doors will then be unlocked if it is safe to do so. If, for example, the wash is too End of your wash cycle At the end of the wash programme the display will indicate `Programme finished'. Remove the washing and turn off the machine by pressing the `Mains on/off' button. Switch off the electricity at the socket and turn off the water supply to the machine. hot after a 85°C cycle, the doors will stay locked until the temperature is safe to allow the doors to be opened. Optional settings To personalise the default wash programmes 8 01 1 Adjust your programme Use these options to adjust the default settings of the wash programmes. On certain programmes some temperature, spin and soil level settings cannot be overridden in order to protect your clothes; see programme table section 9 01. 2 Add options To activate any of the options below after you have selected your programme, press the desired option button once; press again to cancel the option. Minimum iron This option holds your clothes in water after the final rinse to minimise creasing. To protect your clothes, this option is not available on all programmes. 3 Start delay This option allows you to delay the start of the cycle by up to 24 hours. Only available on CRO1 Memory. 4 Door lock The door lock light indicates that the outer door is locked. When a programme is paused the door will unlock if it is safe to do so. Press the `start' button to finish the programme. Pre-wash This option will remove excess dirt Soil level selection guidelines Dirt Select `Dirt' for garments which are only lightly soiled (see programme table for maximum load). [. . . ] Maintenance wash To prevent odours and build-up of deposits within the washing machine, it is recommended that you run a 60° cotton cycle with half a measure of detergent but no clothes 2 or 3 times a year. If the outer door is accidently removed · If further items appear to be blocking the coin trap, pull out the flow accelerator. · If the tray becomes full, turn the cap clockwise into its starting position, empty the tray and repeat the process. New illustration · Using the Dyson spanner, lift the childproof tab and turn the cap anticlockwise. · Wash in warm, soapy water. 1 Locate top ring of outer door into the yellow part of flexible hinge. 2 Lift the door and push forward until lower ring of door "clicks" into place. 1 To replace the coin trap cover: · lubricate the seal with washing up liquid. [. . . ]