User manual VAISALA AWS330

[. . . ] USER'S GUIDE Vaisala Automatic Weather Station AWS330 M211296EN-A PUBLISHED BY Vaisala Oyj P. O. Box 26 FI-00421 Helsinki Finland Phone (int. ): +358 9 8949 1 Fax: +358 9 8949 2227 Visit our Internet pages at www. vaisala. com. © Vaisala 2011 No part of this manual may be reproduced in any form or by any means, electronic or mechanical (including photocopying), nor may its contents be communicated to a third party without prior written permission of the copyright holder. Please observe that this manual does not create any legally binding obligations for Vaisala towards the customer or end user. [. . . ] For instance, in the Initialization command field, you could enter "ATE\rATX1"; that is, multiple AT commands separated by a "\r". Likewise, in the Dial-up command field, you could enter ATDT123456; that is, an AT command immediately followed by a phone number. Save your settings and return to the Address Book window by selecting Save. TCP/IP Socket Connections To add an Address Book entry for a TCP/IP socket connection, proceed as follows: 1. From the Type list, select Client socket or Server socket as the connection type. The fields for selecting the TCP/IP connection parameters, shown in Figure 84 on page 141, are displayed. 140 _________________________________________________________________ M211296EN-A Chapter 5 __________________________________________ Software Configuration and Operation 1101-023 Figure 84 4. 5. Creating TCP/IP Socket Connection Address Book Entry 6. In the Name field, enter an alphanumeric string that uniquely identifies the connection you are creating in the Address Book. If you have multiple QML loggers on the same network and you are going to access them over the same TCP/IP connection, you will need a unique identifier for each logger. To uniquely identify the logger for which you are creating an Address Book entry, enter a unique alphanumeric string in the Station id field. However, if you only have a single logger on the network, you can leave the Station id entry blank. In the Command wait timeout (ms) field, enter a value in milliseconds that specifies for how long AWS Client will wait for the logger to respond when AWS Client sends a requests over the TCP/IP connection. If the request, for instance, a log file download, succeeds within the timeout, a success message is displayed. If the request fails, a failure message is displayed instead, and you have the option to try again at a later time. Factors such as the current load on the logger, delays in the connection, and the response length affect whether or not the timeout will expire during a request. VAISALA ______________________________________________________________________ 141 User's Guide ______________________________________________________________________ 7. In the IP addr. /DNS name field, enter the destination IP address or DNS name. NOTE In order to use the DNS name, you must have access to a DNS server to be able to resolve the DNS name to the IP address of the destination host. NOTE For Server socket, the target IP addr. /DNS name is not available in the user interface. 8. 9. Note that for Client socket, this must match the port set for incoming connections in the interface configuration in the QML logger. For Server socket, Host address and port defined for virtual COM port must match the AWS Client IP address and port. If support for Telnet escape sequences for binary file transfer is required, select the Telnet option. Save your settings and return to the Address Book window by selecting Save. Dial-Up Connections The dial-up connections are based on Windows Dial-Up Networking entries, so you first need to create the connection in Windows. For information on creating Windows Dial-Up Networking connections, please see the Windows online help. To add an Address Book entry for the dial-up connection, proceed as follows: 1. The field for selecting Windows Dial-Up Networking entries is available in the window shown in Figure 85 on page 143. 142 _________________________________________________________________ M211296EN-A Chapter 5 __________________________________________ Software Configuration and Operation 1101-024 Figure 85 4. 5. Creating Dial-Up Connection Address Book Entry 6. In the Name field, enter an alphanumeric string that uniquely identifies the connection you are creating in the Address Book. If you have multiple QML loggers on the same network and you are going to access them over the same dial-up connection, you need a unique identifier for each logger. [. . . ] The sun is considered to be shining, if global radiation (G) is more than 120 W/m2. Also, the ratio G/G0, where G0 is the calculated extraterrestrial global radiation (on top of the atmosphere), must be over 0. 4. Calculation of G0 requires stations position (longitude and latitude), current (= local) time, and day number (0-365). The global radiation G is measured with a pyranometer (CM6B is recommended), using an analog measuring channel. [. . . ]