User manual UNIVERSAL ELECTRONICS EXTENDER

[. . . ] A­B­C "Cable Converter Features" (see converter manual. Slide the door open to reveal less-often used keys such as VCR transport buttons and cable converter features. In the VCR and TV modes, use the REW, PLAY, FF, REC, STOP, and PAUSE keys to control your VCR. This key will also control the input select feature on most TVs. 6 Millennium 4 Mnl M4094 2/29/00 6:21 PM Page 7 INSTALLING BATTERIES 1. [. . . ] If you perform this procedure correctly, the LED will blink twice. NOTE: If the LED did not blink twice after entering the code's last digit, then repeat steps 2 through 3 and try entering the same code again. 3. 4. Aim the Millennium 4 at your TV/VCR Combo and press POWER once. If it does not respond, repeat steps 2-3, trying each code listed for your brand until you find one that works. If it still does not work, try searching for the code (see Searching For Your Code on page 26). If you've located a TV/VCR setup code that works your TV/VCR Combo and a separate TV code is also listed, you'll need to program this code into the Millenium 4 to access volume control (see Programming TV Control on page 8). If there is no separate TV code listed, you will need to perfrom the following steps to access volume control: a. The LED will blink twice. 5. 16 Millennium 4 Mnl M4094 2/29/00 6:21 PM Page 17 6. Write your TV/VCR Combo code in the boxes below for future reference. NOTE: Remember, to use the Millennium 4 to operate your TV/VCR Combo, press VCR first. Setup Codes for TV/VCR Combos: American High Brocksonic Colt Curtis Mathis Daewoo Emerson Funai GE Hitachi HQ Lloyds MGA Magnavox Magnin Memorex Mitsubishi Orion Panasonic Penney Quasar RCA Sansui Sanyo Sears Sharp Sony Symphonic Zenith 0035 (for TV use 0051) 0002, 0294, 0072 0035 (for TV use 0051) 0278 0002, 0294, 0479 0000 0035 (for TV use 0051), 0060 (for TV use 0047), 0048 (for TV use 0093), 0240 0035 (for TV use 0051), 0000 0000 0000 0240 0081 (for TV use 0054), 0035 (for TV use 0051), 0000 0240 0037, 0162 (for TV use 0250) 0048 (for TV use 0093) 0002, 0294, 0479 0035 (for TV use 0051), 0162 (for TV use 0250) 0035 (for TV use 0051), 0240, 0162 (for TV use 0250) 0035 (for TV use 0051), 0162 (for TV use 0250) 0060 (for TV use 0047), 0035 (for TV use 0051), 0048 (for TV use 0093) 0000, 0479 0240 0000, 0037 0048 (for TV use 0093) 0032 (for TV use 0000) 0000 0000 17 Millennium 4 Mnl M4094 2/29/00 6:21 PM Page 18 PROGRAMMING CABLE CONVERTER (OR DBS RECEIVER) CONTROL The Millennium 4 is preprogrammed at the factory to operate the cable converter given to you by your cable company. However, if you have another brand or model of cable converter or satellite receiver that you would like to control, then you'll need to perform the following instructions to unlock the cable key, enter in a new code, and lock the cable key again. To unlock the Cable key: 1. Locate the brand name of your Cable Converter (or Direct Broadcast Satellite Receiver) in the Setup Codes For Cable Converters (or Setup Codes For DBS Receivers) section starting on the next page, and write it in the appropriate space. Cable Converter Brand: ________________ or DBS Receiver Brand: __________________ The brands are listed in alphabetical order with the most popular codes listed first. You will use one of these codes to reprogram the Millennium 4 to operate your Cable Converter or DBS Receiver. Enter the first four-digit code for your Cable Converter or DBS Receiver. If you perform this procedure correctly, the LED will blink twice. NOTE: If the LED did not blink twice after entering the code's last digit, then repeat steps 2 through 3 and try entering the same code again. 3. 18 Millennium 4 Mnl M4094 2/29/00 6:21 PM Page 19 4. Aim the Millennium 4 at your Cable Converter or DBS Receiver and press POWER once. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit. To check for the codes of your other components, repeat steps 1 through 5, but substitute the appropriate key (i. e. , VCR, CBL, or AUDIO) for the (VCR, Cable, or Audio) component you are checking. Write down the codes in the appropriate boxes below. TV Code 6. VCR Code CABLE Code AUDIO ___________________ Code 27 Millennium 4 Mnl M4094 2/29/00 6:21 PM Page 28 PROGRAMMING THE POWER KEY FOR ALL ON/OFF (CABLE MODE ONLY) With the Millennium 4, you can program the POWER key to turn all of your equipment on and off with the press of one button in the Cable mode. In other modes, individual power control is retained, so you can still power on or off your TV, VCR, or audio component independently. Now, when you press CBL once and then press POWER once, the Millennium 4 will direct power to your cable converter, TV, VCR, and audio component and leave the remote control in the Cable mode. 2. 4. * NOTE: If you do not want all of your equipment to power up all of the time, you can shorten step 4 to include only those devices you want to turn on or off. For example, to just power up your TV and Cable Converter, enter the following sequence for step 4: a. Now when you press CABLE once and then press POWER once, the Millennium 4 will only direct power to your Cable converter and TV, and still leave the remote control in the Cable mode. 28 Millennium 4 Mnl M4094 2/29/00 6:21 PM Page 29 RE-ASSIGNING DEVICE KEYS The Millennium 4 can be set up to control a second TV or VCR, or any combination of four home entertainment components. For example, to have the Millennium 4 control a TV, a Cable Converter, and two VCRs, you will need to re-assign the unused AUDIO key to operate the second VCR as follows: 1. On the Millennium 4, press and hold SETUP until the LED blinks twice, then release SETUP. See Programming VCR Control on page 12. To re-assign other device keys, repeat steps 1 through 4 by substituting the key sequence from the following chart for a desired component: To Re-Assign TV as 2nd VCR key: TV as 2nd Audio key: TV as 2nd Cable key: TV back to TV: VCR as 2nd TV key: Perform Key Sequence SETUP - 9 - 9 - 2 - VCR - TV SETUP - 9 - 9 - 2 - AUDIO - TV SETUP - 9 - 9 - 2 - CBL - TV SETUP - 9 - 9 - 2 - TV - TV SETUP - 9 - 9 - 2 - TV - VCR VCR as 2nd Audio key: SETUP - 9 - 9 - 2 - AUDIO - VCR VCR as 2nd Cable key: SETUP - 9 - 9 - 2 - CBL - VCR VCR back to VCR: SETUP - 9 - 9 - 2 - VCR - VCR AUDIO as 2nd TV key: SETUP - 9 - 9 - 2 - TV - AUDIO AUDIO as 2nd VCR key: SETUP - 9 - 9 - 2 - VCR - AUDIO AUDIO as 2nd Cable key: SETUP - 9 - 9 - 2 - CBL - AUDIO AUDIO back to AUDIO: SETUP - 9 - 9 - 2 - AUDIO - AUDIO Upon completion of a re-assignment, the LED will blink twice to confirm your selection. At that time, you will also need to program the Millennium 4 to control the new component (see previous sections on Programming TV Control, Programming VCR Control, Programming Cable Control, or Programming Audio Control). [. . . ] PROBLEM: LED blinks when you press a key, but home entertainment component does not respond. SOLUTION: Make sure you are aiming the Millennium 4 at your home entertainment component and that you are within 15 feet of the component you are trying to control. PROBLEM: The Millennium 4 does not control home entertainment components or commands are not performing properly. SOLUTION: Try all listed codes for the component brand being set up. Make sure all components can be operated with an infrared remote control. Some combo units may require both a TV code and a VCR code for full operation (see page 16). [. . . ]