User manual UNIVERSAL ELECTRONICS NEVO

[. . . ] You will see the Mosaic Welcome screen, followed by the Device screen. USING THE TOUCH SCREEN Mosaic features a Touch Screen that responds to touch commands, whether you use the supplied Stylus or your finger tip. Each time you tap on the screen, you'll see the LED blink and hear a beep tone, which serve as visual and audio confirmation of your command. After 20 seconds of inactivity, Mosaic will turn off the LCD screen to conserve battery life. Setup THEATER TV CBL VCR TV/VID PWR 1 4 7 Prev 2 5 8 0 3 6 9 Enter CONTROLLING DEVICES Tap on next device. Current active device Setup THEATER Current active device VCR Setup THEATER TV CBL Tap on scroll arrow to see other devices. TV CBL VCR Tap on pages to see more Remote Control Keys. TV/VID PWR TV/VID PWR 1 4 7 Prev 2 5 8 0 3 6 9 Enter Remote Control Keys for active device Mosaic UG rev2 8/30/01 9:07 AM Page 1 Touch Screen Control Device User's Guide Mosaic UG rev2 8/30/01 9:07 AM Page 2 NEVO Table Of Contents CHAPTER 1: INTRODUCTION . [. . . ] Try tapping on the Page Arrows to access other remote control functions and then try tapping on the soft keys on each page to test them. 26 Chapter 3: Setting Up Mosaic Mosaic UG rev2 8/30/01 9:07 AM Page 27 USER'S GUIDE SETUP BY SEARCH As an alternative method, you can use Mosaic's search program to find the correct manufacturer's codes to set up your entertainment devices. With this method you first select a device you want to add, then you perform a code test, advancing through one or more types, to find the one that works. On the Device Screen in the upper left corner, tap on Setup. You will see the main SETUP Menu that greets you and asks, "What would you like to configure?Tap on the DEVICE SETUP key. You will see the DEVICE SETUP Menu. NOTE: To return to a previous menu, tap on the ESC key. To return to last-displayed Device Screen, press down on ESC or MUTE for at least 2 seconds. Tap on the BY SEARCH key. You will see the SEARCH Menu. Esc DEVICE SETUP ?What method would you like to use? TV BY BRAND VCR CBL DVD AMP DAT HOME SAT LD CD PHO Tap on BY SEARCH TUN BY CODE TAPE DELETE V. ACC 4. Tap on the device key for the device you want to add (e. g. , VCR). You will see the SEARCH Test Menu (as shown on the next page) that you will use to find a working code. NOTE: Make sure the device you want to add is turned off (i. e. , POWER switch is OFF). continued on next page. . . Setup By Search 27 Mosaic UG rev2 8/30/01 9:07 AM Page 28 NEVO SETUP BY SEARCH (continued) Esc SEARCH Select the device. Esc SEARCH OK Use the test keys to find your device type. Press OK to save. PREV TV CBL DVD AMP DAT HOME SAT LD CD PHO VCR Test NEXT Tap on VCR TUN TAPE V. ACC PWR 1 5. If it does not respond, advance the code test by tapping on the NEXT key and then tap on the PWR key again. If the code is valid, you will see the CODE SETUP ADD/REPLACE menu that lists two choices. NOTE: If the code is not valid, Mosaic will reject it and prompt you to try again. If you make a mistake entering the code, tap the CLEAR key to erase it. Then tap on Esc CODE SETUP Enter the 4 digit code, press OK to save. OK Esc CODE SETUP ? Would you like to ADD the device or REPLACE it with an existing one? Device Code First, enter code. 1234 1 4 7 CLEAR 2 5 8 0 3 6 9 ADD REPLACE 32 Chapter 3: Setting Up Mosaic Mosaic UG rev2 8/30/01 9:07 AM Page 33 USER'S GUIDE · Use the ADD key when setting up a new device (e. g. , a DVD player) that is not currently on the Device Selection Strip (if needed, refer to Using the Touch Screen ­ Selecting a Device on page 18). Use the REPLACE key to replace a device (e. g. , a new TV set) that is currently on the Device Selection Strip. · 6. Tap on the ADD key to add the device to Mosaic's memory. You will see the default device label being added to the Device Selection Strip. NOTE: If you tap on the REPLACE key instead, Mosaic will ask you to select the device to be replaced and, after your selection, if you want to relabel it. However, if the device to be replaced has programmed keys, Mosaic will first ask if you want to keep or clear the settings. 7. · To relabel it, tap on the YES key and you will see the LABEL Menu. Follow the procedure that is similar to the one starting with step 3 on page 54 to relabel the key and tap the OK key when you're done. You will see a confirmation screen that says the key has been successfully programmed. To return to the Device Screen, press on ESC or MUTE for at least 2 seconds. To test remote control of the newly-added device, tap on its key on the Device Selection Strip. Try tapping on the Page Arrows to access other remote control functions and then try tapping on the soft keys on each page to test them. Setup By Code 33 Mosaic UG rev2 8/30/01 9:07 AM Page 34 NEVO DELETING A DEVICE If you no longer use a certain device or it has been incorrectly added to the Device Selection Strip, use the following procedure to delete it from Mosaic's memory. [. . . ] Tap on the PERSONALIZATION key. You will see the PERSONALIZATION Menu. NOTE: To return to a previous menu, tap on the ESC key. To return to last-displayed Device Screen, press down on ESC or MUTE for at least 2 seconds. Tap on the DELETE key. You will see the DELETE MACROS Menu. Esc MACROS ?Esc DELETE MACROS Select a Macro key. Program a sequence of keystrokes onto one key. M1 M2 M3 ADD VIEW COPY Tap on DELETE DELETE ALL continued on next page. . . Using Macros 45 Mosaic UG rev2 8/30/01 9:07 AM Page 46 NEVO USING MACROS DELETING A MACRO (CONTINUED) 5. [. . . ]