User manual UNIVERSAL ELECTRONICS MOSAIC

[. . . ] Mosaic UG rev2 8/30/01 9:07 AM Page 1001 Mosaic UG rev2 8/30/01 9:07 AM Page 1002 MOSAIC INSTALL BATTERIES 1. On Mosaic's back side, push the tab and lift off the battery cover. Match the + and ­ marks on the batteries to the + and ­ marks in the battery case. Align the cover's keys with the opening's holes and press the cover back into place. QUICK START 4. [. . . ] If the device still does not respond, repeat this process, advancing through code tests until you find a code that works. Esc SEARCH OK To check previous code, tap on Use the test keys to find your device type. Press OK to save. PREV VCR Test NEXT If device does not respond, tap and repeat test. First, tap on PWR 1 28 Chapter 3: Setting Up Mosaic Mosaic UG rev2 8/30/01 9:07 AM Page 29 USER'S GUIDE 6. To save a code that works, tap on the OK key. You will see the SEARCH ADD/REPLACE menu that lists two choices. Tap on Esc SEARCH OK Esc SEARCH ? Use the test keys to find your device type. Press OK to save. Would you like to ADD the device or REPLACE it with an existing one? PREV VCR Test NEXT PWR ADD REPLACE 1 · Use the ADD key when setting up a new device (e. g. , a DVD player) that is not currently on the Device Selection Strip (if needed, refer to Using the Touch Screen ­ Selecting a Device on page 18). Use the REPLACE key to replace a device (e. g. , a new TV set) that is currently on the Device Selection Strip. · 7. Tap on the ADD key to add the device to Mosaic's memory. You will see the default device label being added to the Device Selection Strip. NOTE: If you tap on the REPLACE key instead, Mosaic will ask you to select the device to be replaced and, after your selection, if you want to relabel it. However, if the device to be replaced has programmed keys, Mosaic will first ask if you want to keep or clear the settings. 8. · To relabel it, tap on the YES key and you will see the LABEL Menu. Follow the procedure that is similar to the one starting with step 3 on page 54 to relabel the key and tap the OK key when you're done. To keep the label the same, tap on the NO key. continued on next page. . . · Setup By Search 29 Mosaic UG rev2 8/30/01 9:07 AM Page 30 MOSAIC SETUP BY SEARCH (continued) 9. You will see a confirmation screen that says the key has been successfully programmed. To return to the Device Screen, press on ESC or MUTE for at least 2 seconds. To test remote control of the newly-added device, tap on its key on the Device Selection Strip. Try tapping on the Page Arrows to access other remote control functions and then try tapping on the soft keys on each page to test them. 30 Chapter 3: Setting Up Mosaic Mosaic UG rev2 8/30/01 9:07 AM Page 31 USER'S GUIDE SETUP BY CODE Mosaic is a technologically-advanced control device that is designed to be set up using the Set Up By Brand feature described on page 21. This section is reserved for installers and programmers of the Mosaic Touch Screen Control Device who are familiar with setting up devices using manufacturer's 4-digit IR codes. NOTE: Manufacturer's codes are available for customer access on our web site ­ see "About Mosaic" on page 82 for details on locating the URL address. 1. On the Device Screen in the upper left corner, tap on Setup. You will see the main SETUP Menu that greets you and asks, "What would you like to configure?Tap on the DEVICE SETUP key. You will see the DEVICE SETUP Menu. NOTE: To return to a previous menu, tap on the ESC key. To return to last-displayed Device Screen, press down on ESC or MUTE for at least 2 seconds. Tap on the BY CODE key. You will see the CODE SETUP Menu. Esc DEVICE SETUP ?What method would you like to use? TV BY BRAND VCR BY SEARCH TUN CBL DVD AMP DAT HOME SAT LD CD PHO Tap on BY CODE TAPE DELETE V. ACC 4. Tap on the device key for the device you want to add (e. g. , VCR). You will see the DEVICE CODE Menu (as shown on the next page) that you will use to enter a working code. NOTE: Make sure the device you want to add is turned off (i. e. , POWER switch is OFF). continued on next page. . . Setup By Code 31 Mosaic UG rev2 8/30/01 9:07 AM Page 32 MOSAIC SETUP BY CODE (continued) Esc CODE SETUP Select the device. Esc CODE SETUP Enter the 4 digit code, press OK to save. OK Device Code TV CBL DVD AMP DAT HOME SAT LD CD PHO _ Tap on VCR TUN TAPE V. ACC 1 4 7 CLEAR 2 5 8 0 3 6 9 5. [. . . ] Tap on the Macro key you want to delete. You will see a confirmation screen that says the macro key has been successfully deleted from all device screens and the main MACROS Menu. NOTE: Use VIEW/DELETE (see "Chapter 4: Personalizing Mosaic ­ Using View/Delete" on page 65) to delete macros from Device Screens but keep them intact on the main MACROS Menu for future copying. To delete another macro key, tap on the ESC key to return to the DELETE MACROS Menu, or press down on ESC or MUTE for at least 2 seconds to return to the lastdisplayed Device Screen. DELETING ALL MACROS To delete all macros, perform the following steps: 1. On the Device Screen in the upper left corner, tap on Setup. You will see the main SETUP Menu that greets you and asks, "What would you like to configure?Tap on the PERSONALIZATION key. You will see the PERSONALIZATION Menu. NOTE: To return to a previous menu, tap on the ESC key. To return to last-displayed Device Screen, press down on ESC or MUTE for at least 2 seconds. [. . . ]