User manual UNITEC ELECTRONICS WASH SELECT II

[. . . ] Wash Select II POS Operations Manual Unitec Electronics www. unitecelectronics. com WASH SELECT II WASH SELECT II POS OPERATIONS MANUAL SOFTWARE VERSION 5. 53 This manual provides comprehensive operational procedures for the Wash Select II. In this manual, we will discuss the setup, operation and maintenance of the Wash Select II. If further assistance is needed, please contact the distributor from which the product was purchased. When calling for assistance, you must have the following information available: Wash Select II Serial Number: Distributor Name: COPYRIGHT © 2010 Unitec, Incorporated. [. . . ] Printer Paper is out No 24VDC power to printer Printer is either disconnected, malfunctioning, or paper head arm is disengaged. Warning Text Name (Text/TAP) Detailed Description Problem Type Priority (Voice/ Tone) 2 Lower Tolerance Upper Tolerance 1 1 2 HOPPER JAM/EMPTY Warning 2 1 2 3 4 WASH WARNING WASH OUT-OSERV WASH TIMEOUT Warning Fault 2 3 1 1 5 5 5 Warning 1 2 5 6 CREDIT ERROR Warning 1 3 4 7 CASH FRAUD Warning 1 2 3 8 9 10 PRINTER PAPER PRINTER PWR ERR PRINTER ERROR Warning Warning Warning 2 2 2 1 1 1 2 2 2 11 12 13 BILL JAM BILL STACKER FULL BILL FAILURE Warning Warning Warning 2 2 2 1 1 1 1 1 1 Document Number: Document Title: WS21002 WSII Operations Manual ver 5. 53 64 WASH SELECT II Error Code # (Numeric) 14 Text Name (Text/TAP) Detailed Description Problem Type Priority (Voice/ Tone) Lower Tolerance Upper Tolerance CARD READER ERR Multiple "Bad Card reads" (doesn't include bad card orientations) have been registered. Card reader may be faulty or dirty Use this to do a Pager Test Wash Fault Input has been activated This message is never paged, but it will appear on the pager log when it is printed. This page is received when the wash goes back in service after being out of service. Network Login Failed Network Login Success Warning 1 25 25 15 16 17 PAGER TEST WASH FAULT POWER ON Warning Fault 1 3 1 1 99 2 18 WASH IN SERVICE 21 22 LOGIN FAILED LOGIN SUCCESS 1 0 10 1 10 1 2. 10. 3 Programming/Editing Pager Numbers The Wash Select II can be programmed to accommodate specific pager requirements. The following sections provide the settings and descriptions available for programming and editing the wash Select II Pager Number. Document Number: Document Title: WS21002 WSII Operations Manual ver 5. 53 65 WASH SELECT II 2. 10. 3. 1 Numeric Pagers Table 8. Numeric Pager Parameters Setting Phone # (up to 16 digits) Pause After Dial 0 to 120 seconds Description This is the phone number that is dialed to access the numeric pager. This is the normal # that you give a person when you want to have them page you. This is the delay in seconds after the phone number is dialed before proceeding. This compensates for the time it takes for the page company to answer and possibly play a greeting or instructional message. For typical numeric only pagers, a value of 3 to 8 seconds will function properly. Remember that the # of rings before the system will answer can vary from time to time. This is also useful if your system has a voice prompt and requires you to enter several selections to send a page. You may insert 2-second-pauses between digits in the PIN number using one of the wash buttons. If your system requires you to enter a series of options to send the message or set the priority, then add those here. The termination characters will be sent after the numeric message is sent. For example, if you have to press # when finished, and then you have to press 1 to send the page, you would enter: #, 1 The comma will add a 2 second pause after the # key. Pin # (up to 16 digits) Termination Characters (up to 10 digits) Use the following procedure to program or edit the pager number: 1. Using the toggle switch at the top of the CPU board, place the Wash Select II in setup mode by moving the switch toward the back of the Wash Select II case. (The CPU board is located on the inside right wall of the Wash Select II case. ) 2. Using the (3) key to scroll forward and the (1) key to scroll back, scroll through the main menu until the "Paging Functions" option is displayed. Scroll through this menu until the "Edit Pager #" option is displayed, and then press the (*) key to enter. 4. Enter the pager's telephone number including the area code; if it is necessary for the modem to dial a 1 you must enter that as well. [. . . ] This warranty is not transferable to someone other than the original purchaser. WARRANTY PERIOD The Warranty Period on new equipment is 1 year from installation, or 16 months from invoice (whichever occurs first). The warranties in this policy otherwise exclude any labor or installation costs. Unitec will honor warranties expressly provided by another manufacturer for any passthrough purchased item is herein defined. A pass-through purchased item is a system manufactured solely as an assembly by another manufacturer, such as bill validator and coin acceptors, which Unitec purchases and integrates into a Unitec product in accordance with product unit specifications. [. . . ]