User manual UNIDEN XCA650

[. . . ] . 41 43 45 46 50 51 51 52 53 53 55 57 60 62 66 66 68 69 70 71 71 73 75 75 76 77 2 Important Safety Instructions When using your telephone equipment, these basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons: 1. Unplug this product from the wall outlet before cleaning, and use a dry cloth, without liquid or aerosol cleaners. Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Slots and openings in the cabinet and the back or bottom are provided for ventilation. [. . . ] The current Time and Day Stamp and number of new messages recorded is announced in the Handset receiver. 2. Press 5. You will hear a tone in the Handset followed by the announcement: "Answering System on. " 3. Press R Standby. again to return to The talk/batt low LED turns off. 41 4. To turn the Answering System off, press R . The talk/batt low LED lights green. The current Time and Day Stamp and number of messages recorded is announced on the Handset receiver. 5. Press 5. You will hear a tone in the Handset followed by the announcement: "Answering System off. " 6. Press R Standby. again to return to The talk/batt low LED turns off. 42 Base Operation 1. To turn the Answering System on, press answer. A tone sounds, and the current outgoing message plays on the Base Unit speaker. A second tone sounds to indicate the unit is ready to answer calls, and the Message Counter LED turns on. 2. To turn the Answering System off, press answer again. A tone sounds and the Message Counter LED turns off. Setting the Clock The clock in your XCA650 Answering System starts when power is applied to the Base Unit. Press R on the Handset. The talk/batt low LED lights green. 43 2. Press * . Then enter the number which corresponds to the day. 3. Enter the two-digit number for the hour (01-12) and the minute (00-59). To set PM, press #. 4. Note: A beep indicates the new time is programmed, and the new Time and Day Stamp is announced in the Handset receiver. 5. to return to For example, to set Tuesday at 3:20 PM, press R followed by these keys. *30320# Note: Remember to press R again to return to Standby. 44 Reviewing Time and Day Stamp Handset Operation 1. Press R to hear the current Time and Day Stamp. The Handset beeps and the Time and Day Stamp is announced, followed by the total number of messages stored in memory. The talk/batt low LED lights green. 2. Press 6 to replay the current Time and Day Stamp while using the remote keys . The Handset beeps and the Time and Day Stamp is replayed. 3. Press R Standby. again to return to 45 Base Operation 1. Press 6. The speaker beeps, and the Time and Day Stamp is announced. Setting Your Outgoing Message (OGM) When you receive a call, the Answering System answers and automatically plays either a preset message or your personal Outgoing Message. Preset Messages The XCA650 has two messages programmed in its memory. If the REC TIME/ANN/4/1 switch is in either the four or one position, the first preset message below plays. If the switch is set in the left position, (i. e. , the "Announce Only" position) the second message below plays, and no incoming messages are recorded. No one is available to take your call. Note: If the REC TIME/ANN/4/1 switch is in the "Announce Only" position, the Message Counter LED displays an A when the system is in Standby. 46 Recording Your Personal OGM Handset Operation 1. . Note: You can leave up to a 60-second outgoing message. 47 3. Press 6 to stop recording. The message replays in the Handset receiver. 4. Press R Standby. again to return to The talk/batt low LED turns off. 48 Base Operation 1. Start recording your message after you hear the long tone and the Message Counter LED begins to count up. 2. Do not get closer than twelve inches from the microphone, and speak clearly while recording your message. When you are finished recording, release ogm. You hear a tone, and your message is played on the Base Unit speaker. Note: You can leave up to a 60-second outgoing message. 49 Selecting a Preset OGM After you have recorded an outgoing message, you can set your Answering System to play either a preset message or your outgoing message. 1. Press ogm. Your recorded outgoing message will begin to play. 2. While your recorded outgoing message is playing, press ogm again. A tone will sound, and you hear the preset message "Hello. No one is available to take your call, please leave your message after the tone" on the Base Unit speaker. A second tone sounds after the preset message plays, and the Answering System automatically returns to Standby. Note: If the REC TIME/ANN/4/1 switch is set to Announce Only, then the preset message "Hello. [. . . ] (including battery) BT-185 Capacity Talk Mode Standby Mode Battery Save Mode Answering System Memory Type Memory Capacity Message Length Digital Tapeless Recording approx. outgoing message (max. ) 270 mAh, 3. 6V 6 hours 7 days 5 weeks 48. 76 to 49. 99 MHz (25 Channels) 43. 72 to 46. 97 MHz (25 Channels) 120V AC 60 Hz 8 3 in. 18. 9 oz. Specifications, Features, and availability of Optional Accessories are all subject to change without prior notice. 77 XCA650/655 Integrated Telephone Answering Device Extend . A . Phone ® talk talk batt low remote tone ? mem ringer chan flash pause redial Operating Guide UDZZ01369ZZ PRECAUTIONS Before you read anything else, please observe the following: WARNING! Uniden America Corporation DOES NOT represent this unit to be waterproof. [. . . ]