User manual UNIDEN XCA4500

[. . . ] . 46 48 49 49 53 54 54 55 56 56 58 60 62 65 70 71 72 73 74 76 77 77 79 81 81 82 83 2 Important Safety Instructions When using your telephone equipment, these basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons: 1. Do not use this product near water; for example, near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Slots and openings in the cabinet and the back or bottom are provided for ventilation. To protect the product from overheating, these openings must not be blocked or covered. [. . . ] To turn the Answering System OFF, press ANS ON/OFF again. PAGE/FIND A tone sounds and the Message Counter LED turns off. Setting the Clock The clock in your xca4500 Answering System starts when power is applied to the Base Unit. Press Handset. r on the TALK REMOTE TALK BATT LOW ABC The TALK/BATT LOW LED lights orange. 1 2 DEF 1 1 GHI 2 7 JKL 3 3 MNO 4 4 PRS 5 TUV 6 9 WXY 7 8 a 9 46 2. Press * Then enter the number which corresponds to the day. 3. Enter the two-digit number for the hour (01-12) and the minute (00-59). To set a. m. , press * To set p. m. , press # 4. Note: A beep indicates the new time is programmed, and the new Time and Day Stamp is announced in the Handset receiver. 5. Press Standby. r to return to For example, to set Tuesday at 3:20 p. m. , press followed by these keys. r *30320# Note: Remember to press again to return to Standby. r 47 Reviewing Time and Day Stamp Handset Operation 1. Press to hear the current Time and Day Stamp. r TALK REMOTE TALK BATT LOW ABC 4 PRS TUV a WXY The Handset beeps and the Time and Day Stamp is announced, followed by the total number of messages stored in memory. The TALK/BATT LOW LED lights orange. 1 2 DEF 1 1 GHI 2 7 JKL 3 3 MNO 4 7 5 8 6 9 9 REMOTE 2. Press 6 to replay the current Time and Day Stamp while using the remote keys . TALK TALK BATT LOW ABC The Handset beeps and the Time and Day Stamp is replayed, followed by the remaining recording time available for new messages. 1 2 DEF 1 1 GHI 2 7 JKL 3 3 MNO 4 4 PRS 5 TUV 6 9 WXY 7 3. Press again to return to Standby. 8 a 9 r 48 Base Operation 1. Press STOP. NEW MESSAGE Digital Answering System The speaker beeps, and the Time and Day Stamp is announced followed by the remaining recording time available. 0 STOP REPEAT PLAY SKIP DELETE ANS ON/OFF OGM MEMO INTERCOM PAGE/FIND Setting Your Outgoing Message (OGM) When you receive a call, the Answering System answers and automatically plays either a preset message or your personal OGM. Preset Messages The XCA4500 has two messages programmed in its memory. If the REC TIME/ANN-1 switch is in the right position, the first preset message below plays, and all incoming messages are limited to one minute. If the switch is set in the left position, (i. e. , the "Announce Only" position) the second message below plays, and no incoming messages are recorded. No one is available to take your call. REC TIME ANN-1 RING SW PULSE-TONE CPC REC TIME RING VOL 2-5-TS OFF-ON ANN-1 OFF-LO-HI RESET TEL-LINE DC IN 9V + - Note: If the REC TIME/ANN-1 switch is in the "Announce Only" position, the Message Counter LED displays an A when the system is in Standby. 49 Recording Your Personal OGM Handset Operation 1. Press r . TALK REMOTE TALK BATT LOW ABC The TALK/BATT LOW LED lights orange. 1 2 DEF 1 1 GHI 2 7 JKL 3 3 MNO 4 4 PRS 5 TUV 6 9 WXY 7 2. Press 8 a 9 REMOTE 7. TALK TALK BATT LOW ABC Note: You can leave up to a 60-second outgoing message. 1 2 DEF 1 1 GHI 2 7 JKL 3 3 MNO 4 4 PRS 5 TUV 6 9 WXY 7 8 a 9 50 3. Press 6 to stop recording. TALK REMOTE TALK BATT LOW ABC The message replays in the Handset receiver. 1 2 DEF 1 1 GHI 2 7 JKL 3 3 MNO 4 4 PRS 5 TUV 6 9 WXY 7 4. Press to Standby. 8 a 9 r again to return The TALK/BATT LOW LED turns off. 51 Base Operation 1. Start recording your message after you hear the long tone and the Message Counter LED begins to count up. NEW MESSAGE Digital Answering System 0 STOP REPEAT PLAY SKIP DELETE ANS ON/OFF OGM MEMO INTERCOM Press and Hold PAGE/FIND 2. Do not get closer than 12 inches from the microphone, and speak clearly while recording your message. When you are finished recording, release the OGM Button. You hear a tone, and your message is played on the Base Unit speaker. Note: You can leave up to a 60-second outgoing message. 52 Selecting a Preset OGM After you have recorded an outgoing message, you can set your Answering System to play either a preset message or your outgoing message. Press OGM. NEW MESSAGE Digital Answering System Your recorded outgoing message will begin to play. 0 STOP REPEAT PLAY SKIP DELETE ANS ON/OFF OGM MEMO INTERCOM PAGE/FIND 2. While your recorded outgoing message is playing, press OGM again. A tone will sound, and you hear the preset message "Hello. No one is available to take your call, please leave your message after the tone" on the Base Unit speaker. A second tone sounds after the preset message plays, and the Answering System automatically returns to Standby. [. . . ] To reduce the risk of fire, electrical shock, or damage to the unit, DO NOT expose this unit to rain or moisture. RECHARGEABLE NICKEL-CADMIUM BATTERY WARNING This equipment contains a Rechargeable Nickel-Cadmium Battery. Cadmium is a chemical known to the State of California to cause cancer. The Rechargeable Nickel-Cadmium Battery contained in this equipment may explode if disposed of in a fire. Do not charge the Rechargeable Nickel-Cadmium Battery used in this equipment in any charger other than the one designed to charge this battery as specified in this Guide. [. . . ]