User manual UNIDEN XC717

[. . . ] 41 1 Important Safety Instructions When using your telephone equipment, these basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons: 1. Unplug this product from the wall outlet before cleaning, and use a dry cloth, without liquid or aerosol cleaners. Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Slots and openings in the cabinet and the back or bottom are provided for ventilation. [. . . ] Plug one end of the long telephone cord into the TEL LINE jack on the Base Unit. 5. Place the cord inside the molded channel on the bottom of the Base Unit. 6. Place the Base Unit on the screws and push down until it's firmly seated. 17 7. Plug the other end of the telephone line cord into the wall jack. 8. Plug the AC Adapter into a standard 120V AC wall outlet. Note: Do not use an outlet controlled by a wall switch. Setting the Handset Retainer The handset retainer holds the Handset in place if your phone is mounted on a wall. The steps below describe how to remove and replace the retainer so that the tab faces up. Push up on the Handset retainer on the Base Unit, and slide the tab out. 18 2. Push down on the Handset retainer until it snaps into place. 19 Setting Up Your Phone Extending the Antenna Before using your phone, be sure to raise its antenna to the vertical position. Installing the Handset Battery Pack 1. Align the plastic connector of the Nickel-Cadmium battery pack with its socket and plug it in. Note: The black lead will be on the left when the plug is properly aligned. 4. Place the battery pack inside the battery compartment, and slide the battery cover back on. Note: The built-in Memory Backup feature allows up to 3 minutes to disconnect the old battery pack and install a new one without losing any numbers stored in memory. 21 Cleaning the Battery Contacts To maintain a good charge, it is important to clean all charging contacts on the Handset and Base Unit about once a month. Do not use any liquids or solvents. talk flash/rdl talk batt low 1 page/find 2 ghi abc 3 6 9 def 4 25 CHANNEL ULTRACLEAR PLUS 5 8 tone jkl mno Extend·A·Phone 7 pqrs tuv wxyz D mem 0 r. tone pause oper r. vol chan volume Contacts Contacts 22 Charging the Battery Pack Initial Battery Charging The rechargeable Nickel-Cadmium battery pack must be fully charged before using your phone for the first time. We recommend that the battery pack charge for approximately 15-20 hours, without interruption, before plugging the phone line into your new phone. Either place the Handset facedown --or-- Hang the Handset on the cradle when the phone is mounted on a wall. Note: Make sure to change the Handset Retainer before hanging up the phone. 2. If the LED doesn't light, check to see that the AC adapter is plugged in, and that the Handset is making good contact with the Base Unit charging contacts. 23 Charging from the Charging Cradle (Only for the XC700 SERIES phones. ) 1. Plug the Charging Cradle AC Adapter cord into the DC Input Jack on the Charging Cradle. 2. Plug the AC Adapter into a standard 120V AC wall outlet. Note: Do not use an outlet controlled by a wall switch. 4. The red CHARGE LED lights while the unit is charging. talk talk batt low flash/rdl 1 2abc 5 jkl 3def 4ghi 6mno 7 pqrs tone 8 tuv 9 wxyz 0 oper r. tone r. vol chan mem Q pause volume 24 Continuous Battery Charging For the best battery performance, return the Handset to the Base Unit at the end of the day. This keeps the battery fully charged, so your phone works best. Low Battery Indicator When the Battery Pack in the Handset is very low and needs to be charged, the TALK/BATT LOW LED flashes. talk talk batt low flash/rdl 1 4 ghi 7pqrs 2abc 5 jkl 8 tuv 3def 6 mno 9 wxyz If the TALK/BATT LOW LED begins to flash, the phone is programmed to eliminate its functions to save power. The table below describes what to do to return your phone to normal operation. During a Call In Standby Mode Only the Abutton operates. The Handset beeps and the TALK/BATT LOW LED flashes once every 3 seconds. Return the Handset to the Base Unit for charging. None of the buttons will operate. Return the Handset to the Base Unit for charging. Note: Allow 15 to 20 hours without any interruption for the Handset to fully recharge. 25 Setting the Pulse/Tone Switch Be sure the PULSE/TONE switch is in the TONE position. PULSE­TONE Note: Most phone systems are Tone dialing. [. . . ] · If a power failure has occurred and power will be out for some time, remove the battery from the Handset. This will prevent the battery from completely discharging. Hear only continuous static from Handset and phone will not turn off. 40 Specifications General ­ The XC600/700 SERIES complies with FCC Parts 15 and 68. Frequency Control Modulation Operating Temperature Base Unit PLL FM ­ 10° to 50° C 48. 76 to 49. 99 MHz 43. 72 to 46. 97 MHz 120V AC 60 Hz ± 3V AC 81 " (H) x 31 " (W) x 2 1 " (D) 2 2 4 Approx. 43. 72 to 46. 97 MHz 48. 76 to 49. 99 MHz Rechargeable Ni-Cd Battery Pack 7 3 " (H) x 2 " (W) x 2 1 " (D) 4 4 (w/o antenna) Approx. (including battery) BT-185 Capacity 270 mAh, 3. 6V Talk Mode 8 hours Standby Mode 14 days Receive Frequency (25 Channels) Transmit Frequency (25 Channels) Power Requirements Size Weight Handset Receive Frequency (25 Channels) Transmit Frequency (25 Channels) Power Requirements Size Weight Battery Specifications, Features, and availability of Optional Accessories are all subject to change without prior notice. 41 XC 600/700 Series . . Extend A Phone ® e/f pag ind 25 honRePLUS d ·A ·RPACLEA ECxHtAeNnNEL ULT Operating Guide UDZZ01384FZ PRECAUTIONS Before you read anything else, please observe the following: WARNING! Uniden America Corporation DOES NOT represent this unit to be waterproof. [. . . ]