User manual UNIDEN SQ530

[. . . ] 220 V-240 V, 50 Hz/60 Hz. Place the receiver on a flat, level surface. Adequate ventilation is essential to prevent failure of electrical components. Do not place anything heavy on it. Do not remove the cover, as live parts are accessible when it is removed. Avoid location subject to excessive vibration. Do not insert foreign objects into the Ventilation Holes. 2 WARNINGS AND PRECAUTIONS Avoid exposing the Receiver to direct sunlight and other heat sources. Do not damage the AC cord. (If damage occurs, replace immediately to avoid fire or shock hazards. ) To prevent damage which might result in fire or electrical shock hazard, do not expose the Receiver to rain or excessive moisture. ACCESSORIES Check that you have the accessories and items shown Operating Instruction book Remote Control Transmitter EUR511223 Guarantee Card Batteries for the Remote Control Transmitter, (2 x R6(UM3) size) AC cable TSXA151 RGB cable TSXF228 HD/VD cable TSXF229 Audio cable TSXF230 Ferrite sleeve TSK 1027 Clamper Remote control batteries BMake sure that the batteries are fitted the correct way round. Alkaline and Manganese or use rechargeable (Ni-Cad) batteries. 3 QUICK START GUIDE Quick Start Guide 1 Connections L AUDIO VD HD PR/CR/R PB/CB/B Y/G R Wide Plasma Display COMPONENT/RGB IN HD/VD cable (Supplied) (Cable with black plug) * The HD/VD cable has a white line marked on it for identification. Do not connect any other cables to the same signal connector by mistake. [. . . ] Decoder (AV2) Access Access Access AUTO Off 15 TUNING MENU - PROGRAMME EDIT The Programme edit menu allows you to edit the programme position settings. Open the Setup menu Select Move to Tuning menu Setup menu TV/AV TV TOP Off On Access Access Change Exit Access Tuning menu Move to Programme edit menu AV2 out Teletext Off timer Q-Link Tuning menu OSD language Access Programme edit menu Make required changes (see sections below) Select Access Setup menu TV/AV TV TOP Off On Access Access Exit Press STR button to store changes If you have finished in the Programme edit menu, press the TV/AV button to exit. AV2 out Teletext Off timer Q-Link Tuning menu OSD language 1 Select Access Return TV/AV 'STR' Button Exit Store To delete an unwanted programme position Ensure that the cursor is in the Prog. Column CH41 Tuning menu Programme edit Auto setup Manual tuning Fine tuning Colour system Volume correc. Decoder (AV2) Access Access Access AUTO Off Choose the programme position Press the Red button on remote control Press the Red button again to confirm Return TV/AV 'STR' Button Change programme Select option Exit Store If you have finished in the Programme edit menu, press the TV/AV button to exit. Note: The Decoder (AV2) option in the Tuning menu and the TV VCR option in the Programme edit menu are only displayed when Q-Link in the Setup menu has been set to ON. Programme edit Prog. CH41 - - - - Add Name XYZ Lock Off Off Off Off Off Move Sys SC1 SC1 SC1 SC1 SC1 TV VCR 16 TUNING MENU - PROGRAMME EDIT To add a programme position Choose the programme position where the new programme is to be inserted. Return TV/AV 'STR' Button Change programme Select option Exit Store Press the Green button Programme edit Press the Green button again to confirm. CH41 - CH44 - - Add Name XYZ ZXY Lock Off Off Off Off Off Move Sys SC1 SC1 SC1 SC1 SC1 TV VCR Press STR to store If you have finished in the Programme edit menu, press the TV/AV button to exit. To move a programme to another position Choose the programme position to be moved Return TV/AV 'STR' Button Change programme Select option Exit Store Press the Yellow button on remote control. Programme edit Prog. CH41 - CH44 - - Add Name XYZ ZXY Lock Off Off Off Off Off Move Sys SC1 SC1 SC1 SC1 SC1 TV VCR Choose new position. Press the Yellow button again to confirm. Change programme Return TV/AV 'STR' Button Select option Exit Store If you have finished in the Programme edit menu, press the TV/AV button to exit. Programme edit Prog. CH41 - - - CH44 Add Name XYZ Lock Off Off Off Off Off Move Sys SC1 SC1 SC1 SC1 SC1 TV VCR Note: The TV VCR option in the Programme edit menu is only displayed when Q-Link in the Setup menu has been set to ON. ZXY 17 TUNING MENU - PROGRAMME EDIT To tune a programme position Choose the programme position. Change channel Return TV/AV 'STR' Button Select option Exit Store Move the channel column Programme edit Increase or decrease channel number or use the `C' key for Direct Channel Access (see page 7). Prog. CH41 - CH44 - - Name XYZ ZXY Lock Off Off Off Off Off Sys SC1 SC1 SC1 SC1 SC1 Press STR to store. If you have finished in the Programme edit menu, press the TV/AV button to exit. To rename a programme position Change character Return TV/AV 'STR' Button Select option Exit Store Choose the programme position Move to the Name column Programme edit Prog. CH41 - CH44 - - Name XYZ ZXY Lock Off Off Off Off Off Sys SC1 SC1 SC1 SC1 SC1 Choose the new character Move to the next character position Continue until renaming is done. You may wish to make adjustments in the Setup or Sound menus. Setup menu Open the Setup menu. Select Move to your choice. Adjust Setup menu Access adjustments or options. AV2 out Teletext Off timer Colour system Volume correc. Q-Link OSD language TV TOP Off Auto On Access TV/AV Exit Press the TV/AV button to exit. Sound menu Open the Sound menu Select Adjust Move to your choice Sound menu Access adjustments or options. Volume Bass Treble Balance Headphone volume AI Mode TV/AV Exit Press the TV/AV button to exit. On Music 23 Q-LINK Q-Link allows the receiver to communicate with your VCR. This function can be used to automatically turn the power switches of the receiver and the VCR on and off, but it cannot be used to turn the power switch of the Wide Plasma Display on and off. Use the remote control unit to turn the power switch of the Wide Plasma Display on and off. Open the Setup menu Select Move to Q-Link Setup menu TV/AV TV TOP Off On Access Access Change Exit Confirm Q-Link is set to "On" Press the TV/AV button to exit AV2 out Teletext Off timer Q-Link Tuning menu OSD language The VCR must be connected with a SCART lead (full function type) attached between the AV2 socket of the receiver and the appropriate socket on your VCR. Q-Link, NEXTVIEWLINK or similar technology allows the receiver to instruct a compatible VCR to record the programme that is currently being displayed on screen, regardless of the programme position set on the VCR, thus simplifying the process of recording programmes. To record the programme you are currently watching Press the DIRECT TV REC button on the remote control. If the VCR is off, it will automatically switch on when you press the DIRECT TV REC button. A message, sent from the VCR, will appear on screen showing what is being recorded, or if it is not possible to record; VCR recording preset prog VCR recording own tuner VCR is recording the programme signal from its own tuner. If you wish you can switch off the receiver and leave the VCR recording in the normal way. VCR recording TV source VCR is recording the programme signal from the receiver. You must not change programme position or switch off the receiver: if you do, the VCR will automatically stop recording and switch off. No recording TAPE IS PROTECTED The write protection tab on the back of the cassette has been removed. [. . . ] Press the Blue button, select the page number, then press and hold the STR button. to recall this page. Update Display Press the SET UP button to display special functions, followed by the Yellow button to view the TV picture whilst searching for a Teletext page. News Flash When a new flash page has been selected, press SET UP, Yellow, to view the TV picture. When an update is received, the page number will be displayed on screen. [. . . ]