User manual UNIDEN LRD6499SWS

[. . . ] The built-in Safety Warning System (SWSTM) is capable of detecting a hazardous warning signal transmitted on the K-band. The LRD 6299SWS/LRD 6399SWS provides distinct visual and audio alerts to warn you of the presence of X-, K-, and Ka-SuperWideband radar signals as well as IR laser signals. You can drive with confidence when you bring along the LRD 6299SWS/LRD 6399SWS. The LRD 6299SWS/LRD 6399SWS employs Super Stalker Technology (SST), a state-of-the-art electronic system designed to make this radar detector invisible to all current VG-2 radar detector detectors. [. . . ] When you become familiar with all the distinct alert tones, you can operate the LRD 6299SWS/LRD 6399SWS just by listening, devoting your full attention to the traffic in front of you. 6 X K Ka L SWS P 1 2 3 4 CM 123456 1. 7 89 X-Band Signal Indicator -- A green LED lights and blinks to indicate the presence of an X-band radar signal. K-Band Indicator -- An amber (orange) LED lights and blinks to indicate the presence of a K-band radar. Ka-SuperWideband Signal Indicator -- A yellow LED lights and blinks to indicate the presence of a Ka-SuperWideband radar signal. Laser Signal Indicator -- A red LED under L lights and blinks to indicate the presence of a laser signal. SWS Signal Indicator -- When an early warning hazard or informational signal is detected, the yellow SWS LED begins to blink and the amber K-band LED lights. Power-On Indicator -- A green LED under P lights to indicate power is being supplied to the unit and the unit is turned on. LED Signal Strength Meter -- Four LEDs give an accurate visual indication of the strength of radar or laser signals. City Mode Indicator -- A green LED under C lights to indicate that you selected City Mode. Auto Mute Indicator -- A red LED under M lights to indicate that you selected the Auto Mute feature. 2. 3. 4. 5. 6. 9. Note: Every time you turn on the LRD 6299SWS/LRD 6399SWS, a self-test is performed for all LEDs and Alert tones. You will hear in-order four distinct tones for the X-, K-, and Ka-SuperWideband radar bands, as well as for laser. · The power cord does not block the antenna area on the back of the unit. You can use these clips to attach the power cord to the window frame or other parts of the vehicle, keeping it neat and out of the way. Slip the power cord into the clip to hold it securely in place. 10 Replacing the Fuse The cigarette lighter plug contains a 1-ampere fuse to protect it from power surges. To replace the fuse, unscrew the top of the plug. 2. Remove the fuse and replace it with the same type. 3. To replace the top, push in the two metal contacts and twist into place. Note: Your LRD 6299SWS/LRD 6399SWS comes with an extra fuse. 11 Operation You are now ready to enjoy the convenience and security of your LRD 6299SWS/LRD 6399SWS. Please read this section of the Operating Guide carefully to familiarize yourself with the basic operation of this unit. Power On Turn the Volume control to switch on the power. When you power up the LRD 6299SWS/LRD 6399SWS, it performs a self-test of all its circuits. This test takes about 5 seconds, during which you will hear the different alarm tones and see all the LEDs. First, you will hear the X-band alarm for 2 seconds while the X-band indicator, City, and Mute LEDs light. At this setting you can barely hear the audio alert in a quiet environment. Be sure that the Audio Alert Only indicator is off. Auto Mute Operation Press the Mute button to activate the Auto Mute feature. CITY AUDIO MUTE When the Mute indicator is selected, the unit is in Auto Mute Mode. In this mode you hear the full audio alert when a signal is first received. [. . . ] Rain, dew, road splash, or other liquids can damage the internal components and reduce sensitivity of the LRD 6299SWS/LRD 6399SWS. 17 Troubleshooting If your LRD 6299SWS/LRD 6399SWS does not perform up to expectations, try the suggestions listed below. If you cannot get satisfactory results, call the Uniden Customer Service Center at (800) 297-1023, 8:00 a. m. Be sure the connectors (Power LED not on) are properly installed. · Be sure ignition key is ON or in the accessory position. Relocate the unit clear of any obstruction outside the windshield, such as a wiper blade. [. . . ]