User manual UNIDEN EXP97

[. . . ] Also be sure to complete the product registration form and mail it in. 2 w Features · · · · · · · · · · · · · · · 900 MHz Operation EXP93 Charging Cradle Any Key Answer 10-Number Memory Voice Scramble (EXP92 only) Wall Mountable Battery Saving Feature Handset Volume Control Redial and Flash Extended Range and Clarity One-Way Page/Find AutoTalk AutoStandby 40 Channels Tone/Pulse Dialing The EXP90 Series features include AutoTalkTM and AutoStandbyTM. AutoTalkTM allows you to answer a call by just Included with Your EXP90 Series Phone tt ba talk chan talk 3d ef 2ab 1 4g hi c 5 jk 7pq rs l 6m no 9wxy z 8 ton tuv # 0op er e volu sh me rin ger se fla me m ia red l/p au Base Handset Rechargeable Battery AC Adapter Long Telephone Cord EXP93 Only: Charging Cradle and Power Supply Also included: · This Owner's Manual · Other Printed Material · Precautions and Important Safety Instructions If any of these items are missing or damaged, contact your place of purchase. 3 Controls and Functions 1. keypad - touchpad keys 3. tone - special access key for some phone systems 4. [. . . ] Before mounting your cordless telephone, consider the following: Select a location away from electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting screws into the wall. Make sure the wall material is capable of supporting the weight of the base and handset; otherwise, damage to the unit could result. Use #10 screws with anchoring devices suitable for the wall material where the base will be placed. Insert the screws, with their appropriate anchor device, 3 5/16 inches apart. Allow 3/16 of an inch between the wall and screw heads for mounting the phone. 7. Plug the other end of the telephone line into the telephone wall jack. 8. Plug the AC Adapter into a standard 120V AC wall outlet that is not controlled by a wall switch. Use only the AC adapter that came with the phone. 6 Setting Up Your Phone Extending the Antenna Before using your phone, be sure to raise its antenna to the vertical position. w Low Battery Indicator When the Battery Pack in the handset is low and needs to be charged, the batt low led flashes every 3 seconds. Complete your call as quickly as possible, and return the handset to the base for charging. Installing the Battery Pack The memory backup feature allows up to 3 minutes after disconnecting the old battery pack to install a new one without losing any phone numbers stored in memory. NOTE 1. Remove the handset battery cover. w Cleaning the Battery Contacts To maintain a good charge, it is important to clean all battery contacts on the handset and base about once a month. Plug the battery's cable into the handset. NOTE The plastic connectors will fit together only one way. Make sure the battery's connector is properly aligned. Adjusting Ringer/Volume Controls w Ringer Tone and Volume 1. Press G again until you select the ringer tone and volume you want. 3. While you are on a call, press V. w Charging the handset Place the handset on the base to charge. 2. Press V again until you select the receiver volume you want. 7 EXP93 Charging Cradle The extra charging cradle is not a replacement for the base. Put it in a different room than the base so you can recharge the phone on the cradle. Example: You want to use your cordless phone in the kitchen (an area of high interference). Connect the base in a room with low interference (without appliances, televisions or computers); then, put the charging cradle in the kitchen. Plug the charging cradle AC adapter connector into the DC input jack on the back of the charging cradle. Plug the AC adapter into a standard 120V AC wall outlet that is not controlled by a wall switch. [. . . ] · Make sure that the charging contacts on the handset and on the base are clean. · Move the handset and/or base to a different location away from metal objects or appliances and try again. The audio sounds weak and/or scratchy. Can't make or receive calls. · Check both ends of the base telephone line cord. · Make sure the AC adapter is plugged into the base and wall outlet. · Disconnect the AC adapter for a few minutes, then reconnect it. [. . . ]