User manual UNIDEN EXP9200

[. . . ] Back Cover Foldout One Year Limited Warranty 1 Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons, including the following: 1. Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Slots and openings in the cabinet and the back or bottom are provided for ventilation. To protect the product from overheating, these openings must not be blocked or covered. [. . . ] Allow 12 to 16 hours without interruption for the Battery Pack to fully recharge. Or, replace the Handset's Battery Pack with a charged Battery Pack. 13 Cleaning the Battery Contacts To maintain a good charge, it is important to clean all charge contacts on the Handset and Base Unit about once a month. Do not use any liquids or solvents. CONTACTS CONTACTS 14 Using Your EXP 9200 Note: Refer to the foldout located in the back of this Operating Guide to help familiarize you with the features of your cordless phone. Preparing the Base Unit 1. On the Base Unit, select either Pulse Dialing or Tone Dialing, depending on your local service. Set the Base Unit RINGER/VOLUME switch to either "LO" or "HI" enabling the Base Unit to ring when a call or page is received. Note: When a call is ON HOLD at the Handset and the Base Unit is paged, the Base Unit will ring even with the RINGER/VOLUME switch set to "OFF. " Preparing the Handset 1. Set the RING/BATT SAVE switch to "RING" so the Handset will ring when receiving a call. Note: The TALK LED and keypad lights flash when the Handset receives a call regardless of the RING/BATT SAVE switch position. VOL button to set the Handset ringer volume to either low, medium, or high. Note: Ringer volume for the Handset can be set only when the phone is not in use. During a Call Handset Earpiece Volume Press VOL/R . VOL on the Handset to select a high or low volume level in the Handset earpiece. This feature amplifies the earpiece audio through the Monitor Speaker on the Handset so you can monitor a call without having the phone next to your ear. The Handset microphone is turned off during monitoring, so you can consult another person in the room without the caller hearing you. Out of Range Indicator When the Handset is reaching the end of the EXP 9200's range limit, a beep sounds in the earphone every four seconds. If the Handset goes farther out of range, the warning beeps every 1. 5 seconds. You must go back into range within 20 seconds or the call will be dropped. 15 Keypad Lights The Handset Keypad Lights flash when a call is received and remain lit for 10 seconds. The Base Unit rings (two rings for Line 1, three rings for Line 2), and the corresponding green Line LED flashes. The Handset rings (two rings for Line 1, three rings for line 2), and the corresponding green Line LED and Keypad Lights flash. If the Handset is not in the Base Unit, press the flashing Line Button, or TALK to answer the call. --OR-- If the Handset is in the Base Unit, the AutoTalk feature allows you to answer the call by simply picking up the Handset and beginning your conversation. [. . . ] In addition, we recommend that the base not be plugged into a circuit that also powers a major appliance because of the potential for interference. More Than One Cordless Telephone Other cordless phones will not interfere with your EXP 9200. Spread Spectrum Technology and Auto Channel Scan allow your EXP 9200 to operate on a clear frequency at all times. 24 Specifications General Frequency Control Modulation Operating Temperature Base Unit Receive/Transmit Frequency Power Requirements Size Weight Handset Receive/Transmit Frequency Power Requirements Size Weight Battery : 903. 087 to 925. 6131 MHz (23 Channels) : Rechargeable Ni-Cd Battery Pack 3 : 2 3 in. H with antenna 8 8 60mm W X 55mm D X 245mm H with antenna The EXP 9200 complies with FCC parts 15 & 68 : Crystal controlled transmission : Spread Spectrum System : -10° to 50° C : 903. 087 to 925. 6131 MHz (23 Channels) : 120V AC, 60 Hz 5 : 6 3 in. [. . . ]