User manual UNIDEN EXP91

[. . . ] Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons, including the following: 1. Do not use this product near water; for example, near a sink or in a wet area. To protect the product from overheating, do not block or cover any slots or openings in the Base Unit. This product should never be placed near or over a radiator or heat register. [. . . ] Slide the Retainer back into the Base Unit. 900MHz 93tab3 8 Mounting on a Standard Wall Plate The EXP91 is designed to be mounted on a standard AT&T or GTE wall plate. 1. Plug the AC Adapter into the Base Unit. AC ADAPTOR SEE OWNER'S MANUAL 93dskt 2. Place the AC Adapter cord inside the left channel cord holder. DIAL MODE DC IN 9V TEL LINE P· ·T AC ADAPTOR SEE OWNER'S MANUAL 93pwrin 3. Plug the short telephone cord into the phone and the wall plate jack. AC ADAPTOR SEE OWNER'S MANUAL 93plamt1 9 4. Place the Base Unit on the two posts of the wall plate and slide downward to secure. AC ADAPTOR SEE OWNER'S MANUAL 93plamt2 5. Plug the AC Adapter into a standard 120V AC wall outlet. AC ADAPTER Wide Blade widblde1 Note: Use only the AC Adapter supplied with the EXP91. h Route the power cord where it will not create a trip hazard, or where it could become chafed and create a fire or other electrical hazards. 10 Mounting Directly on a Wall If you do not have a standard wall plate, you can mount the EXP91 directly on a wall. Before mounting your cordless telephone, consider the following: · · · Select a location away from electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting screws into the wall. Make sure the wall material is capable of supporting the weight of the Base Unit and Handset; otherwise, damage to the unit could result. Use #10 screws with anchoring devices suitable for the wall material where the Base Unit will be placed. 1. Insert the screws, with their appropriate anchor device, about 3 5/16 inches apart. Allow about 3/16 of an inch between the wall and screw heads for mounting the phone. 3 5/16" 900scrmt 2. Plug the AC Adapter into the Base Unit. AC ADAPTOR SEE OWNER'S MANUAL 93dskt 11 3. Place the AC Adapter cord inside the left channel cord holder. DIAL MODE DC IN 9V TEL LINE P· ·T AC ADAPTOR SEE OWNER'S MANUAL 93pwrin 4. Plug one end of the long telephone cord into the TEL LINE jack on the Base Unit. AC ADAPTOR SEE OWNER'S MANUAL 93teln4 5. Place the telephone cord into the right channel cord holder. AC ADAPTOR SEE OWNER'S MANUAL 93teln3 12 6. Place the Base Unit on the screws and push down until it's firmly seated. After the unit is mounted, raise the antenna. AC ADAPTOR SEE OWNER'S MANUAL 93scwmt 7. Plug the other end of the telephone line into the telephone wall jack. 93teljk 8. Plug the AC Adapter into a standard 120V AC wall outlet. AC ADAPTER Wide Blade widblde1 Note: Use only the AC Adapter supplied with the EXP91. h Route the telephone and power cords where they will not create a trip hazard, or where they could become chafed and create a fire or other electrical hazards. 13 Installing the Battery Pack The built-in Memory Backup feature allows up to 3 minutes after disconnecting the old Battery Pack to install a new one without losing any phone numbers that may be stored in the telephone's memory. To install or replace the rechargeable battery in your phone, follow these steps: Note: 1. If you have difficulty, make sure the battery's connector is properly aligned. 3. Replace the battery cover. 14 For optimum battery performance: · · · Charge the new battery overnight before using your phone. [. . . ] The Maximum Range rating of the EXP91 is meant to be used as a means of comparison against other range claims. Radio Interference Radio interference may occasionally cause interruptions in your conversations. If these noises continue and are too distracting, move to a different location while you are talking on the phone or change channels on your cordless handset. 20 Specifications General Frequency Control Modulation Operating Temperature Phase Locked Loop FM -10° - 50° C Base Unit Transmit Frequency Power Requirements Size Weight 925. 999 ~ 927. 952 MHz (40 Channels) 9V 210mA (from AC Adapter) 5. 3 in. H Approximately 20 oz. Handset Transmit Frequency Size Weight 902. 078 ~ 904. 030 MHz (40 Channels) 2. 2 in. H Approximately 10 oz. Battery Capacity Talk Mode Standby Mode 600 mAH, 3. 6V 7 hours 14 days Specifications shown are typical and subject to change without notice. 21 900-MHz Cordless Phone with Voice Scramble Operating Guide EXP 91 9 00MH z PRECAUTIONS Before you read anything else, please observe the following: WARNING! Uniden America Corporation DOES NOT represent this unit to be waterproof. [. . . ]