User manual UNIDEN EXAI918I

[. . . ] Precautions! Before you read anything else, please observe the following: Warning!Uniden America Corporation DOES NOT represent this unit to be waterproof. To reduce the risk of fire, electrical shock, or damage to the unit, DO NOT expose this unit to rain or moisture. Rechargeable Nickel-Cadmium Battery Warning H This equipment contains a Rechargeable Nickel-Cadmium Battery. H Cadmium is a chemical known to the state of California to cause cancer. [. . . ] A confirmation tone sounds and the display remains on for two seconds. The Status LED on the Base Unit will blink to indicate that the Caller ID on Call Waiting is off. CIDCW OFF ON-1 OFF-0 4. A confirmation tone sounds and the display remains on for two seconds. The Status LED will blink to indicate that the setting has been stored. AUTOTALK OFF ON-1 OFF-0 Setting the AutoTalk Feature To turn AutoTalk on: 1. Press flash/function four times. AUTOTALK OFF ON-1 OFF-0 AUTOTALK ON ON-1 OFF-0 3. A confirmation tone sounds and the display remains on for two seconds. The Status LED on the Base Unit will blink to indicate that the setting has been stored. 18 AUTOTALK ON ON-1 OFF-0 EXAI918 Using Your Phone Please refer to the foldout in front of your operating guide for key positions. When you have connected power and a telephone line to your EXAI918, the phone is in the "standby mode, " ready to receive and make calls. Making Calls 1. For example, 123-4567 Receiving Calls Note: You must subscribe to Caller ID services from your local phone company for the caller's name and number to be displayed. When the phone rings, the LCD displays a calling screen for two rings. If Caller ID information about the person calling is not available, this screen remains on until you answer the call. -- OR -- CIDCW ON 1234567 CIDCW ON 123456 3. If you entered a wrong number, press chan/delete to backspace until the number is erased. LINE ERROR CALLING To cancel making the call, press volume/cancel. 4. The LCD displays the channel number. CH-10 CH-10 If the Caller ID information is received, the LCD displays: -- OR -- KATHLEEN ROL 817-858-3333 Note: If the Handset fails to connect with the Base Unit the Handset beeps and returns to standby mode. 5. During your conversation the LCD displays the call timer. If the signal is invalid, the LCD displays: LINE ERROR UKNOWN NUM. -- OR -- CIDCW ON 00:00:01 If the number of the person calling is a private number, the LCD displays: -- OR -- PRIVATE NAME PRIVATE NUM. When you have finished with the conversation, press talk to hang up. -- OR -- Place the Handset back on the Base Unit. If the name of the person calling is a private name, the LCD displays: -- OR -- PRIVATE NAME 817-858-3333 If the number of the person calling is unknown, the LCD displays: -- OR -- EXAI918 UKNOWN NAME UKNOWN NUM. 19 If the name of the person calling is unknown, the LCD displays: UKNOWN NAME PRIVATE NUM. Redialing the Last Number Called 1. Press talk. Using the Speakerphone To use the speakerphone to answer a call, press speaker on the Base Unit. To hang up, press speaker again. CH-10 CH-10 Note: If the Handset fails to connect with the Base Unit the Handset beeps and returns to standby mode. 3. Press redial/pause. CIDCW ON 1234567 Note: If the last number dialed is longer than 12 digits, the display will scroll to the left until the last number is shown in the display. 4. During your conversation the LCD displays the call timer. Note: Adjust the speakerphone volume by pressing L for louder or M for softer. Answering a Call with AutoTalk Enabled If you have enabled the AutoTalk feature, just remove the Handset from the Base Unit to answer an incoming call. See "Setting the AutoTalk Feature" on page 18 for details on setting AutoTalk. If the Handset is off the Base Unit, press any key to answer an incoming call. Answering a Call without AutoTalk Enabled When the phone rings, pick up the Handset and press talk. . During your conversation the LCD displays the call timer. CIDCW ON 00:00:01 5. When you have finished with the conversation, press talk to hang up. -- OR -- Place the Handset back on the Base Unit. CH-10 CH-10 Using the Flash Key with Call Waiting Note: You must subscribe to call waiting service from your local phone company to use this feature. CIDCW ON 00:00:01 1. While talking you hear the call waiting signal. KATHLEEN ROL 817-858-3333 CIDCW ON 00:00:01 When you are finished with the conversation, press talk to hang up. -- OR -- 2. [. . . ] · Make sure the AC Adapter is plugged into the Base Unit and wall outlet. · Disconnect the AC Adapter for a few minutes, and then reconnect it. · Check for new Caller ID Names/Numbers 33 EXAI918 Answering System Troubleshooting Chart Problem Answering System does not work. · Press the reset button to reset the system after an AC line spike. [. . . ]