User manual UNIDEN EX965

[. . . ] 40 1 Important Safety Instructions When using your telephone equipment, these basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons: 1. Unplug this product from the wall outlet before cleaning, and use a dry cloth, without liquid or aerosol cleaners. Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Slots and openings in the cabinet and the back or bottom are provided for ventilation. [. . . ] Return the Handset to the Base Unit for charging. h Allow 15 to 20 hours without any interruption for the Handset to fully recharge. 25 Cleaning the Battery Contacts To maintain a good charge, it is important to clean all charging contacts on the Handset and Base Unit about once a month. Do not use any liquids or solvents. Setting the Pulse-Tone Switch Be sure the PULSE-TONE switch is in the TONE position. h Most phone systems are Tone dialing. Check with your local phone company if you are not sure whether your system is Tone or Pulse dialing. Adjusting Ringer Controls h Please refer to the foldout in front of your operating guide for key positions. To adjust the ringer volume of your Base Unit, set the RING VOL switch to the desired position. 26 To adjust the Speaker volume of your Base Unit, adjust the VOLUME slide switch until you hear the desired volume. To adjust the ringer volume of your Handset, press vol/can until you hear the desired ringer volume. To adjust the receiver volume, press vol/can while you are on a call. 27 Automatic Digital Code Security To avoid unauthorized calls on your phone, a Digital Code feature was added to the EX 965 phone. The Code is set automatically when you first use the phone. h Please refer to the foldout in front of your operating guide for key positions. To change the Digital Code, be sure the Handset is on the Base, then: 1. Place the Handset back on the Base Unit while it's still beeping. 4. 5. When the beeping stops, briefly remove the Handset again, and then return it to the Base Unit. The Status LED on the Base Unit will blink to indicate that the Digital Security Code is set to one of the more than 65, 000 codes. h If the Base Unit loses power while the Handset is off the Base, the Digital Code may be erased. When this happens, the Handset will not function. 28 To reestablish communication between the Handset and Base Unit: 1. The status LED on the Base Unit will blink to indicate that the Digital Security Code is set. 29 Programming Your EX 965 h Refer to the foldout located in the front of this Operating Guide for key positions. Storing Memory Dial Numbers Numbers can be stored for use by the Base Unit and the Handset separately. There are 10 memory locations for the Base Unit, and 10 memory locations for the Handset. This feature allows you to place two separate memory calls, one from each active line, at the same time. h Numbers stored with the Handset cannot be accessed by the Base Unit. Numbers stored with the Base Unit cannot be accessed by the Handset. Entering Base Unit Memory Numbers For example, to store the number 555-1212 in the Base Unit memory: 1. The speaker LED blinks and you hear a beep. 2. Enter the number 5551212 on the Base Unit keypad. You may enter a delay between numbers (for accessing a switchboard, or long distance service) by pressing the pause button on the Base Unit at the point in the number sequence you wish to pause. Pressing pause more than once will increase the length of the pause between numbers. Press mem and a number ( 0-9 ) from the Base Unit keypad for the memory location. After pressing mem the second time, you have 20 seconds to enter the number you wish to store. Write the stored number and its memory location number on one of the enclosed stickers. h 3. h 4. 30 Entering Handset Memory Numbers For example, to store the nunmber 555-1212 in the Handset memory: 1. The LCD displays: You may enter a delay between numbers (for accessing a switchboard, or long distance service) by pressing the ch/pause button on the Handset at the point in the number sequence you wish to pause. Pressing ch/pause more than once will increase the length of the pause between numbers. Press mem. 2. h 3. 4. Enter a number ( 0-9 ) from the Handset keypad for the memory location. After pressing mem the second time, you have 20 seconds to enter the number you wish to store. [. . . ] s Cadmium is a chemical known to the State of California to cause cancer. s The Rechargeable Nickel-Cadmium Battery contained in this equipment may explode if disposed of in a fire. s Do not charge the Rechargeable Nickel-Cadmium Battery used in this equipment in any charger other than the one designed to charge this battery as specified in this Guide . Using another charger may damage the battery or cause the battery to explode. [. . . ]