User manual UNIDEN CEZ200

[. . . ] The warranty is invalid if the Product is (A) damaged or not maintained as reasonable or necessary, (B) modified, altered, or used as part of any conversion kits, subassemblies, or any configurations not sold by Uniden, (C) improperly installed, (D) serviced or repaired by someone other than an authorized Uniden service center for a defect or malfunction covered by this warranty, (E) used in any conjunction with equipment or parts or as part of any system not manufactured by Uniden, or (F) installed or programmed by anyone other than as detailed by the owner's manual for this product. STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any time while this warranty is in effect, warrantor will either, at its option, repair or replace the defective unit and return it to you without charge for parts, service, or any other cost (except shipping and handling) incurred by warrantor or its representatives in connection with the performance of this warranty. Warrantor, at its option, may replace the unit with a new or refurbished unit. THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] Do not use the telephone to report a gas leak in the vicinity of the leak. SAVE THESE INSTRUCTIONS Uniden works to reduce lead content in our PVC coated cords in our products and accessories. Warning!The cords on this product and/or accessories contain lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. Uniden® is a registered trademark of Uniden America Corporation. Your actual phone may not look exactly like the pictures. Page 1 (outside) Fold line Fold line Fold line Fold line Using the Phone Boost button Volume dial Reset button Visual ringer light Flash button Tone/ pulse switch Mute button Redial button Hook switch Handset clip Ringer switch Button What it does Boost and These controls work together to change the volume. Flash During a call: switch to a waiting call Tone/pulse Change the dial mode (see Solving Problems. ) Reset During a call: Hang up the current call and get a dial tone. During a call: press & hold to mute the microphone so callers Mute can't hear you. Ringer Turn the audio ringer (but not the visual ringer) off or on. Wall-Mounting the Phone You can mount the phone on any standard telephone wall plate where the pins are 100 Connect the cords as usual, but route the mm (315/16 inches) line cord through apart. Before putting the handset in the cradle, you need to switch the Tuck excess line cord into the handset space on the back of the phone. clip into wall mount mode as shown in Line up the notches on the the drawing base with the pins on the below. Place the phone over the plate and slide it down to lock it into place. If there's static on the line DSL broadband Internet service can cause static on telephones, but a DSL filter usually solves any problems. To get a DSL filter, call your DSL provider or look in any electronics store. To install the filter, plug the DSL filter into the wall jack and then plug your phone into the filter. FCC compliance information Part 68 information DSL lter Telephone wall jack Telephone cord What Else Do I Need to Know? This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US: 6NYTE##BXXXXXX (where XXXXXX stands for a specific model number). An applicable Universal Service Order Codes (USOC) certification for the jacks used in this equipment is provided (i. e. , RJ11C) in the packaging with each piece of approved terminal equipment. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. [. . . ] Contact the state public utility commission, public service commission or corporation commission for information. NOTICE: According to telephone company reports, AC electrical surges, typically resulting from lightning strikes, are very destructive to telephone equipment connected to AC power sources. To minimize damage from these types of surges, a surge arrestor is recommended. Flip the clip from front to back. Slide the clip out of its slot. Slide it back into the slot. Rotate the clip 180 degrees. Using Call Waiting Call waiting is service provided by your local telephone provider; contact your telephone provider to subscribe to this service. Press Flash to switch between the current call and the waiting call; each time you switch, there's a short pause before you're connected to the other caller. [. . . ]