User manual UNIDEN BCD396T

[. . . ] BCD396T OWNER'S MANUAL OWNER'S MANUAL Precautions Before you use Precautionsthis scanner, please read and observe the following. This scanning radio has been manufactured so that it will not tune to the radio frequencies assigned by the FCC for cellular telephone usage. The Electronic Communications Privacy Act of 1986, as amended, makes it a federal crime to intentionally intercept cellular or cordless telephone transmissions or to market this radio when altered to receive them. The installation, possession, or use of this scanning radio in a motor vehicle may be prohibited, regulated, or require a permit in certain states, cities, and/or local jurisdictions. [. . . ] The currently-selected menu item is highlighted with a bar on the display. When the menu item you want to select is highlighted, briefly press the scroll control to select it. To find information about a particular menu setting in this manual, go to the page number shown in parentheses next to the setting. Note: Not all of the options shown in this table may appear at the same time. To view all available options on any screen, rotate the scroll control. Menu Item -- M E N U -Program System Srch/CloCall Opt Search for . . . Submenu Select System System1 System2 System3 (51) -- M E N U -Program System Srch/CloCall Opt Search for . . . Srch/CloCall Opt Freq Lockouts Broadcast Screen CTCSS/DCS Search Srch/CloCall Opt Repeater Find Max Auto Store Set Delay Time Set Modulation Set Attenuator Set Data Skip Set Step Adjust P25 Level Search for . . . Service Search Edit Service Custom SearchOpt Srch/CloCall Edit Custom Search and Store (107) (108) (95) (109) (110) (112) (90) (110) (110) (111) (112) (81) -- M E N U -Program System Srch/CloCall Opt Search for . . . (94) (98) (96) (97) (100) Note: the actual Select System submenu display will depend on what is programmed into the scanner. Using the Menu 49 Menu Item -- M E N U -Srch/CloCall Opt Search for . . . Close Call Submenu Close Call Close Call Only CC Auto Store Set CC Mode Set CC Override Set CC Alert Set CC Bands Set Priority Off On Plus On Srch/CloCall Opt (104) (104) (104) (104) (104) (104) (54) (54) (54) (54) -- M E N U -Search for . . . Close Call Set Priority -- M E N U -Close Call Set Priority WX Operation WX Operation Weather Scan Weather Alert Program SAME Opt Srch/CloCall Set Delay Time Set Attenuator WX Alt Priority Tone-Out for . . . Tone-Out Standby Tone-Out Setup h/ l ll (113) (113) (114) (112) (110) (115) -- M E N U -Set Priority WX Operation Tone-Out for . . . (116) (116) -- M E N U -WX Operation Tone-Out for . . . Xfer Information Xfer Information Wired Clone On-Air Clone h/ l ll (57) (58) -- M E N U -Tone-Out for . . . Xfer Information Settings Settings Set Backlight Adjust Key Beep Set Battery Save Srch/CloCall Opt Set Audio AGC Adjust Contrast PC Control See Scanner Info (54) (53) (54) (55) (55) (56) (53) Using the Menu 50 Programming Systems Menu This table shows the scanner's systems menu structure. To find information about a particular menu setting in this manual, go to the page number shown under or next to the setting. To use the systems menu, press Menu then briefly press the scroll control. Note: Not all of the options shown in this table may appear at the same time. To view all available options on any screen, rotate the scroll control Menu/ Submenu Select Sys Type Conventional MOT EDCS Srch/CloCall Op LT "Programming Conventional Systems" on Page 61 Option Menu System 1 C Edit Name Edit Sys Option Edit Group Srch/CloCall Opt Delete System Copy System (74) (75) (61) (83) (83) Select Sys Type Conventional MOT EDCS Srch/CloCall Op LT "Programming Motorola Systems" on Page 63 System 1 M System 1 P25 800MHz Standard 800MHz Splinter Srch/CloCall Op 900MHz band VHF Band UHF Band Select Sys Type Conventional MOT EDCS LT "Programming EDACS Systems" on Page 67 Edit Name Edit Sys Option Set Frequencies Srch/CloCall Opt Set Modulation Set Attenuator Edit Group Delete System Copy System (74) (75) (71) (65) (83) (66) (83) (83) System 1 E Edit Name Edit Sys Option Set Frequencies Opt Srch/CloCall Set Attenuator Edit Group Delete System Copy System (74) (75) (71) (83) (66) (83) (83) EDCS WIDE NARROW SCAT Srch/CloCall Opt Using the Menu 51 Menu/ Submenu Select Sys Type Conventional MOT EDCS Srch/CloCall Op LT "Programming LTR Systems" on Page 70 Option Menu System 1 L Edit Name Edit Sys Option Set Frequencies Opt Srch/CloCall Set Modulation Set Attenuator Edit Group Delete System Copy System (74) (75) (71) (65) (83) (71) (83) (83) Using the Menu 52 Other Settings Other Settings Displaying System Information Viewing Memory Used Menu Settings See Scanner Info % Memory Used A bar showing the percent of memory used appears. Press any key to return to the previous menu, then press Scan or Hold. Viewing the Firmware Version Menu Settings See Scanner Info Firmware Version Press any key to return to the previous menu, then press Scan or Hold. Adjusting the Key Beep Menu Settings Adjust Key Beep Auto - the scanner automatically sets the key beep to match the master volume setting level you select. Off - the scanner turns the key beep off. Locking/Unlocking the Keypad and Scroll Press and hold down Func then press / / to lock or unlock the keypad. Keypad Lock and On (if the keypad is locked) or Off (if the keypad is unlocked) appears. The scroll control still controls the volume when you lock the controls. Other Settings 53 Turning Power Save On or Off Menu Settings Set Battery Save · On The scanner goes into low-power mode when you monitor a conventional channel that has no activity. · Off Power save is off. Priority Scan Menu Set Priority Func Or, while holding on any channel, press to select one of these priority modes: · Off Normal scanning + 1/Pri · On While scanning a conventional system, the scanner interrupts every 2 seconds and checks the priority channels in each unlocked conventional system. Priority channels in lower priority key numbered systems (starting from 1) have highest priority. [. . . ] By default, all of the preprogrammed systems are unlocked, and your scanner begins to scan them when you turn it on. To speed up scanning, you can lock out systems that are beyond your reception area (typically no more than 25 miles using the supplied antenna). While continuing to hold Func , rotate the scroll control to select a system you want to lock out. While continuing to hold out the system. Func , press L/O to lock 4. [. . . ]