User manual UNIDEN BC92XLT

[. . . ] BC92XLT Paper OM. fm Page 1 Tuesday, August 24, 2004 3:56 PM BC92XLT OWNER'S MANUAL OWNER'S MANUAL BC92XLT Paper OM. fm Page 2 Tuesday, August 24, 2004 3:56 PM Precautions Before you use Precautions this scanner, please read and observe the following. This scanning radio has been manufactured so that it will not tune to the radio frequencies assigned by the FCC for cellular telephone usage. The Electronic Communications Privacy Act of 1986, as amended, makes it a federal crime to intentionally intercept cellular or cordless telephone transmissions or to market this radio when altered to receive them. The installation, possession, or use of this scanning radio in a motor vehicle may be prohibited, regulated, or require a permit in certain states, cities, and/or local jurisdictions. [. . . ] SRCH appears and the scanner searches starting with the weather service bank. When the scanner stops on a transmission, press Hold to stop searching and listen to the transmission. In this mode, you can Operation 34 BC92XLT Paper OM. fm Page 35 Tuesday, August 24, 2004 3:56 PM press Func + frequencies. or Func + to step through the To release the hold and continue searching, press Hold. Or, if you did not press Hold, simply press Func + or Func + to continue searching. Note: Because there are many different frequencies allocated to fire and police departments, it can take several minutes to search all the service frequencies. Storing Frequencies into Channels During Service Search You can store frequencies you found during service search or service search hold mode into channels. If you want to select another channel, press Func + or Func + before you press E. If you entered a frequency that has already been entered elsewhere, the scanner sounds an error tone and displays the channel that was duplicated. If you entered the frequency by mistake, press then enter the correct frequency. To enter the frequency anyway, press E to accept. Scanning the Stored Channels To begin scanning channels, press Scan. The scanner scans through all non-locked channels in the activated banks. (See "Locking Out Channels" on Page 48 and "Turning Channel-Storage Banks On and Off" on Page 47). When the scanner finds a Operation 35 BC92XLT Paper OM. fm Page 36 Tuesday, August 24, 2004 3:56 PM transmission, it stops on it. Notes: · · If you have not stored frequencies into any channels, the scanner does not scan. If the scanner picks up unwanted partial, or very weak transmissions, turn Squelch clockwise to decrease the scanner's sensitivity to these signals. To listen to a weak or distant station, turn Squelch counterclockwise. To ensure proper scanning, adjust Squelch until the audio mutes. · Manually Selecting a Channel You can continuously monitor a single channel without scanning. This is useful if you hear an emergency broadcast on a channel and do not want to miss any details - even though there might be periods of silence - or if you want to monitor a specific channel. To manually select a channel, press Hold, enter the channel number then press Hold again. Or, during scanning, if the radio stops at a channel you want to listen to, press Hold once. (Repeatedly pressing Hold at this time causes the scanner to step through the channels. ) Press Scan to resume automatic scanning. Operation 36 BC92XLT Paper OM. fm Page 37 Tuesday, August 24, 2004 3:56 PM Special Features SpecialCallTM RF Capture Technology Close Features Your scanner's Close Call feature lets you set the scanner so it detects then displays the frequency of a nearby strong radio transmission. Close Call RF capture works great for finding frequencies at venues such as malls and sporting events. You can set the scanner so Close Call detection works "in the background" while you are scanning other frequencies, turn off normal scanning while Close Call is working, or turn off the Close Call feature and use the scanner normally. [. . . ] ­20°C to +60°C Close Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 channels per second (max) Search Rate Normal . . . . . . . . . . . . . . . . . . . . . . . . . . 180 steps per second (max) Priority Sampling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 dB Specifications 57 BC92XLT Paper OM. fm Page 58 Tuesday, August 24, 2004 3:56 PM IF Frequencies 1st IF (25-174 MHz). . . . . . . . . . 380. 6050-380. 7000 MHz 1st IF (406-512 MHz) . . . . . . . 380. 6125-380. 7000 MHz 1st IF (806-956 MHz) . . . . . . . 380. 7000-380. 7875 MHz 2nd IF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]