User manual UNIDEN 202

[. . . ] Released electrolyte is corrosive and may cause damage to the eyes or skin. Exercise care when handling the battery(ies) in order not to short the battery(ies) with conducting materials such as rings, bracelets, and keys. The battery or conductor may overheat and cause burns. 1 Press PRG. or w until "L1 Ring" current setting will be displayed 3 Thesecond line of the display. [. . . ] Oprima OFF o PRG para terminar la sesión de programación. 1 vo 2 OprimaCode". w hasta que aparezca "Sec Oprima PRG (Programa) en el nuevo auricular. Oprima "#" 3 programar elpara comenzar a código de seguridad. HANDSET LOW BATTERY INDICATOR When the battery pack needs recharging, the low battery icon will be displayed. You may also notice a reduction in the quality of your cordless handset communications. Return the handset to the charging station as soon as possible, whenever the low battery icon is on. 2 Calls can now be made using the headset. return using the handset without 3 Toheadset, tosimply unplug the headset. a INSTALLING THE BELT CLIP of clip into 1 Place one sidesidethe belt handset. the groove on the of the side of 2 Snap the otherthe otherthe belt clip into the groove on side of the handset. Expansion Handset for 2. 4 GHz Spread Spectrum Multiple-Handset Cordless Telephone EASY TO USE OWNER'S GUIDE SYSTEM REGISTRATION (SECURITY CODE) All handsets must be programmed with the SAME security code (Sec. If you don't remember the system security code, refer to one of the handsets already in-use to obtain the code. INITIAL SETUP Congratulations!You have purchased one of the most sophisticated and versatile cordless telephone systems available. The handset will function as either a one-line or a two-line phone, depending on which base unit you have purchased. Please note that this handset must be connected to a multiple handset system base. Once the handset is programmed with the same Security Code as the base unit, it will immediately function as part of the system. For detailed instructions to operate your multiple handset system, please refer to the Owner's Guide included with the system Starter set. PROGRAMMING THE SYSTEM SECURITY CODE INSTALL THE CHARGING CRADLE Connect the AC adapter to the back of the charging cradle and plug into an electric outlet. VIEWING THE SYSTEM SECURITY CODE on a system 1 Press PRG (Program)in-use. Press "#" to 3 security code. begin programming the INSTALL THE HANDSET BATTERY Slide open the battery compartment cover and connect the NiMH battery pack as shown in the illustration below. or w (on of the 2 Press v until "Sec the side displays. handset) Code" Sec Code 123456 4 Using the keypad, enter the 6-digit code. PRG end 5 Press OFF or sessiontoOR the programming press v or w to advance to another programming step. system was already operating 6 If your you added the additional before handset, the new handset now will be ready to work as part of the system. are 7 If youtime, setting-up the system for the first please refer to the system Owner's Guide for instructions on how to program the base unit security code. 3 The 6-digit code displayed on the second line is your system security code. to program all PACKING LIST Please take a moment to locate and identify the components shipped with your Cordless Handset. Enclosed within the packaging: s Cordless Handset s Charging Cradle s AC Adapter s Belt Clip s Battery Pack CHARGING THE BATTERY MH-202 M1S1 12/00 Printed in China Place the handset in the charging cradle. The battery will fully charge after approximately 10-12 hours. NOTE: s Make sure you don't confuse the System Security Code with the Handset ID number. Each handset must have the SAME System Security Code, but they must have DIFFERENT Handset ID numbers. IMPORTANT SAFETY INSTRUCTIONS INSTALLATION INSTRUCTIONS 1. [. . . ] Adjust only those controls that are covered by the operating instructions because improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation. Avoid using a telephone (other than a cordless type) during an electrical storm. You should use ONLY the power adapter supplied with your telephone. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ]