User manual ULINE ORIGINS SP-18

[. . . ] Use and Care Guide Ice Maker Models: BI95, BI98, SP18 BI95 BI98 SP18 1 Introduction Congratulations on your purchase of a U-Line refrigeration product. A pioneer in the field for more than 40 years, U-Line Corporation is the world's number one manufacturer of built-in, under-counter, specialty refrigeration and ice making products. U-Line dedicates 100% of its research and development to these products. The result: U-Line technology consistently leads the market with innovation, design, depth of product line and performance. [. . . ] Remove the cabinet door if equipped and secure all interior shelves to the interior of the cabinet using a heavy duty cloth or package sealing tape. Interior Cleaning (As Required) · Turn unit off. Clean the interior and all removed components using a mild non-abrasive detergent and warm water solution applied with a soft sponge or non-abrasive cloth. These types of cleaners may transmit taste to the interior products and damage or discolor the interior. BI95, BI98, SP18 9 Maintenance Proper maintenance of your U-Line product will ensure efficiency, top performance and long life. You may want to shorten the intervals if you have pets or other special considerations. 7. Dampen a soft sponge or non-abrasive cloth in clean water and wipe down the cabinet interior and ice bucket to remove any detergent residue. Rinse the sponge or cloth in clean water and repeat as necessary until the cabinet and ice bucket are clean. IMPORTANT DO NOT place ice bucket in dishwasher. Dishwasher will warp/discolor ice bucket and render it useless. Defrosting Manual Defrost Models - Every Two Months (Minimum) Condenser Cleaning Interval - Every Three Months To maintain operational efficiency, keep the front grille free of dust and lint, and clean the condenser every three months. Depending on environmental conditions, more or less frequent cleaning may be necessary. WARNING DO NOT use any type of electrical heating device, ice pick, knife or other sharp instrument to defrost; this could damage the inner lining or refrigeration system and void the warranty. WARNING Disconnect electric power to the unit before cleaning the condenser. To remove and replace the grille for access to the condenser fins, follow this procedure: 1 ULIN_0238_A Figure 8 ULIN_0239_A 1. Clean the interior and ice bucket using a mild non-abrasive detergent and warm water solution applied with a soft sponge or non-abrasive cloth. With a standard blade screwdriver or 1/4" nut driver, remove the grille screw (Figure 8, 1). The condenser fins are SHARP and can be easily damaged. IMPORTANT DO NOT use any type of cleaner on the condenser unit. Clean the condenser coil using a soft brush with a "combing" action or vacuum cleaner. Place the two hook-hinges (located on the rear bottom side of the grille) on the front lip of the unit base. Swing the grille up into position, aligning the grille and cabinet screw hole. 10 BI95, BI98, SP18 6. Re-connect the water supply hose connector (Figure 10, 1) to the water solenoid valve (Figure 10, 2). Open the water main supply valve and check for leaks at the water hose connection. Place the two hook-hinges (located on the rear bottom side of the grille) on the front lip of the unit base. Swing the grille up into position, aligning the grille and cabinet screw hole. Shut off the water at the main supply valve. Ice Maker Maintenance Inlet Screen Interval - Every Twelve Months The solenoid valve inlet screen must be cleaned at least once each year as follows: WARNING Disconnect electrical power to the unit before cleaning the solenoid valve. Pull the unit out to access the back panel. 2 ULIN_0238_A Figure 9 3. With a standard blade screwdriver or 1/4" nut driver, remove the grille screw (Figure 9, 1). [. . . ] Water level set too high REMEDY Models SP18, 95, 98, CO29 and CO75 are manual defrost (See MAINTENANCE; DEFROSTING). Soft sounds from the fan and water/dropping sounds from the ice maker will be heard. Set cube size smaller (See MAINTENANCE; ICE MAKER; ICE CUBE THICKNESS ADJUST). Set cube size smaller (See MAINTENANCE; ICE MAKER; ICE CUBE THICKNESS ADJUST). 16 BI95, BI98, SP18 This page intentionally left blank BI95, BI98, SP18 17 This page intentionally left blank 18 BI95, BI98, SP18 U-Line Corporation Limited Warranty U-Line Corporation warrants each U-Line product to be free from defects in materials and workmanship for a period of one year from the date of purchase; and warrants the sealed system (consisting of the compressor, the condenser, the evaporator, the hot gas bypass valve, the dryer and the connecting tubing) in each U-Line product to be free from defects in materials and workmanship for a period of five years from the date of purchase. [. . . ]